Total 50 results found for the keyword of "eos section 21 3 vxlan configuration"
... ID, along with the extended
communities of tunnel type (MPLS), MPLS Label value and
route-target.
Note: You require Release eos 4.21.1F and later versions with Jericho/Jericho+
platforms.
EVPN vxlan ...
Integrated Routing and Bridging
In traditional data center design, inter-subnet forwarding is provided by a centralized
router, where traffic traverses across the network to a centralized routing ...
... it is binding a label. Note: All connected interfaces are advertised
as bound. However, eos currently advertised labels for /32 addresses, and FEC filter
is configured to install only x.x.x.200/32
prefixes. ...
Inter-VRF Local Route Leaking
Inter-VRF local route leaking
allows the leaking of routes from one VRF (the source VRF) to another
VRF (the destination VRF) on the same router. Inter-VRF routes can ...
VCS to EVPN Hitless Migration
VCS to EVPN Hitless Migration enables support for migrating from only using VCS as the control plane to only using EVPN as a control plane in a hitless manner with respect ...
... offers an echo function. eos supports
asynchronous mode and the echo function.
Asynchronous Mode
Demand Mode
Asynchronous Mode
In asynchronous mode, BFD control packets are exchanged by neighboring ...
IGMP and IGMP Snooping
IGMP Snooping
IGMP Host Proxy
Description
Supported Features
IGMP Protocols
Configuring IGMP
Configuring IGMP Snooping
IGMP Host Proxy
IGMP and IGMP Snooping
Commands ...
Protocol Independent
Multicast
Protocol Independent Multicast
(PIM) distributes multicast data using routes gathered by other protocols.
Arista switches support two types of PIM: PIM Sparse Mode ...
Multicast Source Discovery Protocol (MSDP)
Multicast Source Discovery
Protocol (MSDP) describes a topology that connects multiple IPv4 Protocol
Independent Multicast Sparse-Mode (PIM-SM) domains. ...
Audio Video Bridging (AVB)
Arista switches support Audio Video Bridging (AVB) and the associated protocols. This section describes AVB concepts and the implementation of associated protocols.
Topics ...
... distributes operational state information across a set of eos switches to support applications that provide network services. See the CloudVision User Guide, https://www.arista.com/en/support/product-documentation, ...
... for OSPFv2 adjacencies with DR Other neighbors.
OSPFv2 Multiple Instances Support
eos Release 4.22.1F adds support for multiple OSPFv2 instances to
be configured in the default VRF. OSPFv2 Multiple ...
... area and interface levels.
Note: On the same area or interface, eos allows security configuration with either AH or ESP but not both. We can have one area or interface configured with AH and another ...
...
Note: Unlike node segments, anycast segments do not have the ‘N’ flag set described in section 2.1.1.2 of RFC8667.
The following enhancements are available by release:
eos Release 4.22.1F adds support ...
... hop resolution semantics of BGP routes with an ordered list, or profile, of resolution RIB domains (for example, either tunnel or IP domain). This allows eos to direct specific services over the specified ...
... snooping is a Layer 2 feature that is
configured on LAN switches. The Arista eos switch supports Option-37 insertion that
allows relay agents to provide remote-id information in DHCP request packets. DHCP
servers ...
... and destination
addresses..
ACLs can also be made dynamic (not persisting in the eos), and the
payload keyword can be used to
turn an ACL into a User-Defined Field (UDF) alias for use in other ACLs. ...
VRRP and VARP
A virtual IP (VIP) address
is an IP address that does not directly connect to a specific interface.
Inbound packets sent to a Virtual IP address are redirected to a physical
network ...
Decap Groups
These sections describe the Decap groups:
Decap Groups Description
Decap Groups configuration
Decap Commands
Decap Groups Description
The decap group is a data structure that ...
Global Knob to Set MTU for all Layer 3 Interfaces
Global Layer 3 Maximum Transfer Unit (MTU) feature provides a CLI command to set the MTU value for all Layer 3 interfaces.
The default value for ...