Total 50 results found for the keyword of "eos section 21 4 vlan configuration commands"
... is the protocol used to manage
the membership of hosts in multicast groups for IPv6.
RFC 3810 talks about MLDv2 functionality. MLDv2 is the IPv6 counterpart of IGMPv3. Beginning with eos Release 4.25.0F, ...
IGMP and IGMP Snooping
IGMP Snooping
IGMP Host Proxy
Description
Supported Features
IGMP Protocols
Configuring IGMP
Configuring IGMP Snooping
IGMP Host Proxy
IGMP and IGMP Snooping
commands ...
Protocol Independent
Multicast
Protocol Independent Multicast
(PIM) distributes multicast data using routes gathered by other protocols.
Arista switches support two types of PIM: PIM Sparse Mode ...
Multicast Source Discovery Protocol (MSDP)
Multicast Source Discovery
Protocol (MSDP) describes a topology that connects multiple IPv4 Protocol
Independent Multicast Sparse-Mode (PIM-SM) domains. ...
Audio Video Bridging (AVB)
Arista switches support Audio Video Bridging (AVB) and the associated protocols. This section describes AVB concepts and the implementation of associated protocols.
Topics ...
VXLAN Description
These sections describe VXLAN architecture, the data objects that comprise a VXLAN network, and
process of bridging packets through a VXLAN network.
VXLAN Architecture
VXLAN Gateway ...
... distributes operational state information across a set of eos switches to support applications that provide network services. See the CloudVision User Guide, https://www.arista.com/en/support/product-documentation, ...
Routing Information Protocol (RIP)
This chapter contains the following sections.
RIP Conceptual
Overview
Running RIP
on the Switch
Configuring RIP on Multiple VRFs
RIP commands
RIP Conceptual ...
... for OSPFv2 adjacencies with DR Other neighbors.
OSPFv2 Multiple Instances Support
eos Release 4.22.1F adds support for multiple OSPFv2 instances to
be configured in the default VRF. OSPFv2 Multiple ...
... area and interface levels.
Note: On the same area or interface, eos allows security configuration with either AH or ESP but not both. We can have one area or interface configured with AH and another ...
...
Note: Unlike node segments, anycast segments do not have the ‘N’ flag set described in section 2.1.1.2 of RFC8667.
The following enhancements are available by release:
eos Release 4.22.1F adds support ...
... hop resolution semantics of BGP routes with an ordered list, or profile, of resolution RIB domains (for example, either tunnel or IP domain). This allows eos to direct specific services over the specified ...
...
Maintenance Mode configuration
Maintenance Mode commands
Overview
Using maintenance mode, you can perform several maintenance activities such as:
eos image upgrade.
Initial configuration or ...
... snooping is a Layer 2 feature that is
configured on LAN switches. The Arista eos switch supports Option-37 insertion that
allows relay agents to provide remote-id information in DHCP request packets. DHCP
servers ...
... and destination
addresses..
ACLs can also be made dynamic (not persisting in the eos), and the
payload keyword can be used to
turn an ACL into a User-Defined Field (UDF) alias for use in other ACLs. ...
VRRP and VARP
A virtual IP (VIP) address
is an IP address that does not directly connect to a specific interface.
Inbound packets sent to a Virtual IP address are redirected to a physical
network ...
... that are configured by a custom agent using the eos SDK or eAPI
and age out (expire) after a specified time period.
For example, if you are using a custom agent that reacts to traffic sent to the CPU ...
Decap Groups
These sections describe the Decap groups:
Decap Groups Description
Decap Groups configuration
Decap commands
Decap Groups Description
The decap group is a data structure that ...
Nexthop Groups
These sections describe the Nexthop groups:
Nexthop Group Description
Nexthop Group configuration
Support for IPv6 Link-Local Addresses in Nexthop Groups Entries
Nexthop Group commands ...
Global Knob to Set MTU for all Layer 3 Interfaces
Global Layer 3 Maximum Transfer Unit (MTU) feature provides a CLI command to set the MTU value for all Layer 3 interfaces.
The default value for ...