Total 42 results found for the keyword of "eos section 38 6 multicast commands"
Routing Information Protocol (RIP)
This chapter contains the following sections.
RIP Conceptual
Overview
Running RIP
on the Switch
Configuring RIP on Multiple VRFs
RIP commands
RIP Conceptual ...
... for OSPFv2 adjacencies with DR Other neighbors.
OSPFv2 Multiple Instances Support
eos Release 4.22.1F adds support for multiple OSPFv2 instances to
be configured in the default VRF. OSPFv2 Multiple ...
... hop resolution semantics of BGP routes with an ordered list, or profile, of resolution RIB domains (for example, either tunnel or IP domain). This allows eos to direct specific services over the specified ...
...
Maintenance Mode Configuration
Maintenance Mode commands
Overview
Using maintenance mode, you can perform several maintenance activities such as:
eos image upgrade.
Initial configuration or ...
... snooping is a Layer 2 feature that is
configured on LAN switches. The Arista eos switch supports Option-37 insertion that
allows relay agents to provide remote-id information in DHCP request packets. DHCP
servers ...
... and destination
addresses..
ACLs can also be made dynamic (not persisting in the eos), and the
payload keyword can be used to
turn an ACL into a User-Defined Field (UDF) alias for use in other ACLs. ...
... that are configured by a custom agent using the eos SDK or eAPI
and age out (expire) after a specified time period.
For example, if you are using a custom agent that reacts to traffic sent to the CPU ...
Nexthop Groups
These sections describe the Nexthop groups:
Nexthop Group Description
Nexthop Group Configuration
Support for IPv6 Link-Local Addresses in Nexthop Groups Entries
Nexthop Group commands ...
Segment Security
Overview of MSS-Group
Configuring MSS-Group
Limitations
Show commands
Segment Security
commands
Overview of MSS-Group
Hosts and networks can be grouped into segments ...
Spanning Tree Protocol
Spanning Tree Protocols prevent
bridging loops in Layer 2 Ethernet networks. Arista switches support
Rapid Spanning Tree, Multiple Spanning Tree, and Rapid-Per VLAN Spanning
Tree ...
... Configuration
Procedures
VLAN Configuration
commands
VLAN Introduction
Arista switches support industry standard 802.1q VLANs. Arista eos provides tools to manage and extend VLANs throughout the ...
Layer 2 Protocol Forwarding
Layer2 (L2) Protocol Forwarding on Ethernet interfaces is supported, in addition to
Type-5 PW. Also, selective forwarding of certain L2 Protocol packets
(tagged/untagged/all) ...
... ensure disable-vrf configuration to take effect.
switch(config)# agent SandL3Unicast terminate
SandL3Unicast was terminated
Starting from the eos Release 4.26.0F, /32 prefix length optimization ...
...
eos is optimized to support QoS configuration on the Fabric interfaces on 7250x and 7300 series switches. Configuring QoS on the Fabric interfaces in addition to front panel ports allows user to have ...
... 32-bit
integer used in the candidate path selection
algorithm to select the “active” candidate path.
The default value for preference is
100.
Binding SID (BSID): an optional,
SID.Note: In eos, a BSID ...
... (eos release
4.25.2F)
Support of 400GBASE-ZR with Open Forward Error Correction (O-FEC) (eos release
4.25.2F)
Override a transceiver slot’s maximum power limit (eos release
4.25.2F)
Platform Compatibility ...
... (also configured as a dynamic LAG) on the partner switch. The maximum number of ports per LAG varies by platform; numbers for each platform in the latest eos release are available here: https://www.arista.com/en/support/product-documentation/supported-features. ...
... MLAG peer switches are identical platforms and run identical eos images. Running different images/platform may result in a failure to form an association with the MLAG peer or see discrepancy in behavior. ...
... Type Ports
---- ----------- ---- -----
Total Mac Addresses for this criterion: 0
Beginning with eos Release 4.26.0F,
PortSec-Protect enforces a limit on the number of MAC
addresses, ...
...
MACsec Licensing
MACsec encryption is a eos licensed feature. A valid MACsec license must be configured on a switch. MACsec licenses are tied to a switch serial number and the licensee. ...