- Written by Rajesh Velandy
- Posted on April 22, 2024
- Updated on April 24, 2024
- 2609 Views
Bidirectional Protocol Independent Multicast (PIM) allows routers to build trees to deliver multicast traffic from sources to receivers. It is a variant of sparse-mode PIM that efficiently addresses the use case where receivers for a multicast group are also sources for that group.
- Written by Vamsi Anne
- Posted on December 29, 2021
- Updated on November 19, 2024
- 10416 Views
As Ethernet technologies made their way into the Metropolitan Area Networks (MAN) and the Wide Area Networks (WAN), from the conventional enterprise level usage, they are now widely being used by service providers to provide end-to-end connectivity to customers. Such service provider networks are typically spread across large geographical areas. Additionally, the service providers themselves may be relying on certain internet backbone providers, referred to as “operators”, to provide connectivity in case the geographical area to be covered is too huge. This mode of operation makes the task of Operations, Administration and Maintenance (OAM) of such networks to be far more challenging, and the ability of service providers to respond to such network faults swiftly directly impacts their competitiveness.
- Written by Satish Somanchi
- Posted on August 26, 2019
- Updated on September 5, 2019
- 8582 Views
4.22.1F introduces support for ip address virtual for PIM and IGMP in MLAG and Vxlan. On a VLAN, the same IP address can
- Written by Shelly Chang
- Posted on October 24, 2024
- Updated on October 24, 2024
- 446 Views
This solution allows delivery of both IPv4 and IPv6 multicast traffic in an IP-VRF using an IPv6 multicast in the underlay network. The protocol used to build multicast trees in the underlay network is IPv6 PIM-SSM.
- Written by Chitra Ramachandran
- Posted on April 18, 2024
- Updated on July 31, 2024
- 3096 Views
Multicast VRF leak allows multicast traffic from a sender in one domain or VRF to be forwarded to a different domain or VRF, in which the receivers are connected. In the rest of this document, the VRF to which the multicast sender belongs to is referred to as the “source VRF” and the VRF that the multicast receiver belongs to is referred to as the “receiver VRF”.
- Written by Shelly Chang
- Posted on August 23, 2022
- Updated on August 29, 2022
- 6104 Views
This feature allows PIMv4 to work with Multiprotocol BGP (MP-BGP), where IPv4 prefix routes are reachable via IPv6 next-hops.
- Written by Gokul Unnikrishnan
- Posted on March 1, 2024
- Updated on March 1, 2024
- 2974 Views
The purpose of this feature is to mitigate multicast traffic loss when a switch that is using PIM sparse mode as its multicast routing protocol is going under maintenance.
- Written by Swati Patel
- Posted on August 23, 2019
- Updated on August 23, 2019
- 6951 Views
In a Mlag setup with Pim SSM, one peer becomes the DR for a layer 3 interface and is responsible for routing multicast
- Written by Saravanan Balasubramanian
- Posted on September 11, 2023
- Updated on September 13, 2023
- 4690 Views
In a modular system there are two supervisors which ensures redundancy in event of Hardware and software failures. At any given time, only one supervisor is in control (managing most hardware, including all the linecards). We call it the active supervisor. The other supervisor is called standby supervisor, which serves as a backup in case the active supervisor fails. Stateful switchover is the transition when the standby supervisor takes over control of the entire system from the active supervisor (and therefore becomes the new active). This document describes PIM SSO works and its limitations.
- Written by Santosh Kumar
- Posted on December 22, 2017
- Updated on May 2, 2024
- 7232 Views
PIM Static Source Discovery (SSD) is a feature implemented as part of PIM-SM. Familiarity with setting up and configuring PIM-SM (Sparse Mode) and PIM-SSM (Source-Specific Multicast) is assumed.
- Written by Sabarinath Timma Mohan
- Posted on August 31, 2023
- Updated on August 31, 2023
- 4598 Views
PIM Reverse Path Forwarding (RPF) is a mechanism that allows the multicast routers to send the PIM control packets to the upstream routers via the shortest path to form the RP/Source Tree.
- Written by Shelly Chang
- Posted on January 6, 2022
- Updated on May 3, 2024
- 8658 Views
This feature introduces hardware forwarding support of IPv4 multicast traffic over IPv4 GRE tunnel interfaces in Arista Switches. Multicast source traffic can reach the receivers which are separated by an IP cloud which is not configured for IP multicast routing by utilizing a GRE tunnel.