Total 21 results found for the keyword of "eos section 8 4 environment commands"
environment commands
environment Control
Configuration commands
environment fan-speed
environment insufficient-fans action
environment overheat action
locator-led
environment Display
commands ...
Precision Time Protocol (PTP) commands
PTP commands
ptp announce interval
ptp announce timeout
ptp delay-mechanism
ptp delay-req interval
ptp domain
ptp enable
ptp forward-v1
ptp hold-ptp-time ...
Switch environment Control
The following sections describe the commands that display temperature, fan, and power supply
status:
environment Control Introduction
environment Control Overview
Configuring ...
...
The following running-config file lists the environment
overheat action command.
switch# show running-config
! Command: show running-config
! device: switch (DCS-7150S-64-CL, eos-4.13.2F)
ip route ...
... clusters. This means the directly connected
TaskTracker nodes can belong to different clusters. eos supports a maximum of five
clusters per switch.
MapReduce Tracer Configuration
The MapReduce Tracer ...
Latency Analyzer (LANZ)
Arista Networks’ Latency Analyzer (LANZ) is a family of eos features that provide enhanced
visibility into network dynamics, particularly in areas related to the delay packets
experience ...
... timestamp
Drop count
Device ID
Egress
interface
FCS type
Reserved
TAP Aggregation Extra MPLS Pop (4 to 6 Labels)
Available starting with eos Release 4.23.1F extra MPLS pop for TAP
Aggregation ...
... STP state. When an interface used as an Ethernet segment does not have a forwarding
state, eos considers the interface to be inactive. For a VLAN-based service, the port must be in a forwarding state
on ...
Audio Video Bridging
(AVB)
Arista switches support Audio Video Bridging (AVB) and the associated protocols. This section
describes AVB concepts and the implementation of associated protocols.
Topics ...
... Beginning with eos Release 4.25.0F, MLDv2 snooping is supported on MLAG deployments.
Limitations
The extraneous “Switch” interface should be ignored in show mld
snooping counters and show mld snooping
counters ...
... area
and interface levels.
Note: On the same area or interface, eos allows security configuration with either AH or ESP but not
both. We can have one area or interface configured with AH and
another ...
... This allows eos to direct specific services over the specified RIB domains, overriding the default behavior. Further, this feature, through the use of user-defined tunnel RIBs, empowers an administrator ...
... distributes operational state information across a set of eos switches to support applications that provide network services. See the CloudVision User Guide, https://www.arista.com/en/support/product-documentation, ...
... OSPFv2 adjacencies with DR Other neighbors.
OSPFv2 Multiple Instances Support
eos Release 4.22.1F adds support for multiple OSPFv2 instances to
be configured in the default VRF. OSPFv2 Multiple Instances ...
VRRP and VARP
A virtual IP (VIP) address
is an IP address that does not directly connect to a specific interface.
Inbound packets sent to a Virtual IP address are redirected to a physical
network ...
... often use prefix lists to filter routes.
The RACL divergence optimizes hardware resource usage on each forwarding ASIC. eos installs ACLs only on the hardware components corresponding to the member interfaces ...
...
Before eos Release 4.24.2F, eos supported shaping only on L2
subinterfaces of parent Ethernet interfaces, for example,
Et1.1. Beginning with eos Release
4.24.2F, eos supports shaping on L2 subinterface ...
... control access to eos commands. Three data services conduct authentication, authorization, and accounting (AAA) activities: a local security database, TACACS+ servers, and RADIUS servers.
The Configuring ...
Upgrades and Downgrades
This chapter describes the
procedures for upgrading or downgrading the switch software.
This chapter contains these sections:
Upgrade/Downgrade Overview
Smart System Upgrade ...
7130 Platform Layer 1 Configuration
This section describes the purpose, behavior, and configuration of the 7130 platform and includes the following topics:
Configuring Layer 1 on 7130 Platform
Interface
Addressing ...