Total 33 results found for the keyword of "eos 2 1 initial switch access"
... validating the eos image on your ZTP server by confirming that its MD5 checksum matches the MD5 checksum that can be found on the eos download page of the Arista website. On a UNIX server, the md5sum ...
...  Drop count Device ID Egress interface FCS type Reserved TAP Aggregation Extra MPLS Pop (4 to 6 Labels) Available starting with eos Release 4.23.1F extra MPLS pop for TAP Aggregation ...
initial Configuration and Recovery This chapter describes initial configuration and recovery tasks. Subsequent chapters provide details about features introduced in this chapter. This chapter contains ...
... 1 stop bit. If you do not know the current settings, restore the factory-default settings as described in Restoring the Factory Default eos Image and Startup Configuration. The no boot console and default ...
...  show traffic-engineering database Use the show traffic-engineering database to display the topology used for CSPF computations. Starting from eos Release 4.23.1F, the SRLG group details of a neighbor ...
... can request or change. The agent gathers data from the MIB and responds to requests for information. For a list of supported MIBs, refer to the release notes for the specific eos version. This chapter ...
... ID, along with the extended communities of tunnel type (MPLS), MPLS Label value and route-target. Note: You require Release eos 4.21.1F and later versions with Jericho/Jericho+ platforms. EVPN VxLAN ...
... is the protocol used to manage the membership of hosts in multicast groups for IPv6. RFC 3810 talks about MLDv2 functionality. MLDv2 is the IPv6 counterpart of IGMPv3. Beginning with eos Release 4.25.0F, ...
IGMP and IGMP Snooping IGMP Snooping IGMP Host Proxy Description Supported Features IGMP Protocols Configuring IGMP Configuring IGMP Snooping IGMP Host Proxy IGMP and IGMP Snooping Commands ...
Protocol Independent Multicast Protocol Independent Multicast (PIM) distributes multicast data using routes gathered by other protocols. Arista switches support two types of PIM: PIM Sparse Mode ...
Routing Information Protocol (RIP) This chapter contains the following sections. RIP Conceptual Overview Running RIP on the switch Configuring RIP on Multiple VRFs RIP Commands RIP Conceptual ...
... for OSPFv2 adjacencies with DR Other neighbors. OSPFv2 Multiple Instances Support eos Release 4.22.1F adds support for multiple OSPFv2 instances to be configured in the default VRF. OSPFv2 Multiple ...
... area and interface levels. Note: On the same area or interface, eos allows security configuration with either AH or ESP but not both. We can have one area or interface configured with AH and another ...
...  Note: Unlike node segments, anycast segments do not have the ‘N’ flag set described in section 2.1.1.2 of RFC8667. The following enhancements are available by release: eos Release 4.22.1F adds support ...
... hop resolution semantics of BGP routes with an ordered list, or profile, of resolution RIB domains (for example, either tunnel or IP domain). This allows eos to direct specific services over the specified ...
... snooping is a Layer 2 feature that is configured on LAN switches. The Arista eos switch supports Option-37 insertion that allows relay agents to provide remote-id information in DHCP request packets. DHCP servers ...
... and destination addresses.. ACLs can also be made dynamic (not persisting in the eos), and the payload keyword can be used to turn an ACL into a User-Defined Field (UDF) alias for use in other ACLs. ...
VRRP and VARP A virtual IP (VIP) address is an IP address that does not directly connect to a specific interface. Inbound packets sent to a Virtual IP address are redirected to a physical network ...
Spanning Tree Protocol Spanning Tree Protocols prevent bridging loops in Layer 2 Ethernet networks. Arista switches support Rapid Spanning Tree, Multiple Spanning Tree, and Rapid-Per VLAN Spanning Tree ...
... Locking Commands IP Locking IP Locking is an eos feature configured on an Ethernet Layer 2 port. When enabled, IP Locking ensures that a port will only permit IP and ARP packets with IP source ...