Total 37 results found for the keyword of "eos 3 4 switch platforms"
switch Environment Control
The following sections describe the commands that display temperature, fan, and power supply
status:
Environment Control Introduction
Environment Control Overview
Configuring ...
... label, and be mounted to the same mount
point with the same options. This makes it possible to boot the eos again by installing
a new boot-config and eos SWI, then rebooting (which can be done using
Aboot/fullrecover). ...
...
Drop count
Device ID
Egress interface
FCS type
Reserved
TAP Aggregation Extra MPLS Pop (4 to 6 Labels)
Available starting with eos Release 4.23.1F extra MPLS pop for TAP Aggregation ...
Latency Analyzer (LANZ)
Arista Networks’ Latency
Analyzer (LANZ) is a family of eos features that provide enhanced visibility
into network dynamics, particularly in areas related to the delay packets
experience ...
... displays
information about the active flows maintained in the eos.
Command Mode
EXEC
Command Syntax
show flow tracking sampled flow-table [
detail | dst-ip |
dst-port | group |
interface | protocol ...
... available for other eos applications.
With hardware acceleration, all sFlow processing is done in hardware
using specialized chips, called accelerators. These accelerators
process sampled packets and ...
... can request or change. The agent gathers data from the MIB and responds to requests for information. For a list of supported MIBs, refer to the release notes for the specific eos version.
This chapter ...
... leaks in eos or customer user processes.
Process leaks to too many processes or scripts running at one time.
Over configuration of the system requiring more memory than available.
Large number of temporary ...
Sample Configurations
EVPN VXLAN IRB Sample Configuration
In the topology below, we are connecting a Layer 2 site with a Layer 3 site using Layer 3
EVPN (type-5 route). Right side leaves are MLAG ...
BGP/MPLS L3 VPN
Border Gateway Protocol/ Multiprotocol Label switching (BGP/MPLS) L3 Virtual rivate Network (VPN)
allows a Service Provider (SP) or an Enterprise to provide the
service of interconnecting ...
EVPN MPLS Shared ESI Label
In a multihomed EVPN MPLS configuration, BUM packets sent from a Non-Designated Forwarder
(Non-DF) PE to a Designated Forwarder (DF) PE must carry the ESI label advertised ...
... ID, along with the extended
communities of tunnel type (MPLS), MPLS Label value and
route-target.
Note: You require Release eos 4.21.1F and later versions with Jericho/Jericho+
platforms.
EVPN VxLAN ...
Integrated Routing and Bridging
In traditional data center design, inter-subnet forwarding is provided by a centralized
router, where traffic traverses across the network to a centralized routing ...
VXLAN DSCP Mapping
VXLAN DSCP Mapping allows selecting Differentiated Services Code Point
DSCPand Traffic Class TC values for packets
at VTEPs ( VXLAN Tunnel Endpoint) along VXLAN encapsulation and ...
... offers an echo function. eos supports
asynchronous mode and the echo function.
Asynchronous Mode
Demand Mode
Asynchronous Mode
In asynchronous mode, BFD control packets are exchanged by neighboring ...
... is the protocol used to manage
the membership of hosts in multicast groups for IPv6.
RFC 3810 talks about MLDv2 functionality. MLDv2 is the IPv6 counterpart of IGMPv3. Beginning with eos Release 4.25.0F, ...
... identifier or
a single Customer Edge (CE) to the participating multiple Provider Edge
(PE). The default mode of operation is All-active. Introduced in the
eos 4.26.0F for VxLAN, singe-active is
another ...
... for OSPFv2 adjacencies with DR Other neighbors.
OSPFv2 Multiple Instances Support
eos Release 4.22.1F adds support for multiple OSPFv2 instances to
be configured in the default VRF. OSPFv2 Multiple ...
...
Note: Unlike node segments, anycast segments do not have the ‘N’ flag set described in section 2.1.1.2 of RFC8667.
The following enhancements are available by release:
eos Release 4.22.1F adds support ...
Ingress and Egress Per-Port for IPv4 and IPv6 Counters
This feature provides support for per-interface ingress and egress packet and byte counters for both IPv4 and IPv6.
This section describes Ingress ...