Total 21 results found for the keyword of "eos section 24 5 ipv4 route scale"
... and destination
addresses..
ACLs can also be made dynamic (not persisting in the eos), and the
payload keyword can be used to
turn an ACL into a User-Defined Field (UDF) alias for use in other ACLs. ...
... ensure disable-vrf configuration to take effect.
switch(config)# agent SandL3Unicast terminate
SandL3Unicast was terminated
Starting from the eos Release 4.26.0F, /32 prefix length optimization ...
...
Drop count
Device ID
Egress interface
FCS type
Reserved
TAP Aggregation Extra MPLS Pop (4 to 6 Labels)
Available starting with eos Release 4.23.1F extra MPLS pop for TAP Aggregation ...
Integrated Routing and Bridging
In traditional data center design, inter-subnet forwarding is provided by a centralized
router, where traffic traverses across the network to a centralized routing ...
... offers an echo function. eos supports
asynchronous mode and the echo function.
Asynchronous Mode
Demand Mode
Asynchronous Mode
In asynchronous mode, BFD control packets are exchanged by neighboring ...
... is the protocol used to manage
the membership of hosts in multicast groups for IPv6.
RFC 3810 talks about MLDv2 functionality. MLDv2 is the IPv6 counterpart of IGMPv3. Beginning with eos Release 4.25.0F, ...
IGMP and IGMP Snooping
IGMP Snooping
IGMP Host Proxy
Description
Supported Features
IGMP Protocols
Configuring IGMP
Configuring IGMP Snooping
IGMP Host Proxy
IGMP and IGMP Snooping
Commands ...
... identifier or
a single Customer Edge (CE) to the participating multiple Provider Edge
(PE). The default mode of operation is All-active. Introduced in the
eos 4.26.0F for VxLAN, singe-active is
another ...
... for OSPFv2 adjacencies with DR Other neighbors.
OSPFv2 Multiple Instances Support
eos Release 4.22.1F adds support for multiple OSPFv2 instances to
be configured in the default VRF. OSPFv2 Multiple ...
... area and interface levels.
Note: On the same area or interface, eos allows security configuration with either AH or ESP but not both. We can have one area or interface configured with AH and another ...
...
Note: Unlike node segments, anycast segments do not have the ‘N’ flag set described in section 2.1.1.2 of RFC8667.
The following enhancements are available by release:
eos Release 4.22.1F adds support ...
... hop resolution semantics of BGP routes with an ordered list, or profile, of resolution RIB domains (for example, either tunnel or IP domain). This allows eos to direct specific services over the specified ...
...
Maintenance Mode Configuration
Maintenance Mode Commands
Overview
Using maintenance mode, you can perform several maintenance activities such as:
eos image upgrade.
Initial configuration or ...
... snooping is a Layer 2 feature that is
configured on LAN switches. The Arista eos switch supports Option-37 insertion that
allows relay agents to provide remote-id information in DHCP request packets. DHCP
servers ...
... Configuration
Procedures
VLAN Configuration
Commands
VLAN Introduction
Arista switches support industry standard 802.1q VLANs. Arista eos provides tools to manage and extend VLANs throughout the ...
... Locking Commands
IP Locking
IP Locking is an eos feature configured on an Ethernet Layer 2 port.
When enabled, IP Locking ensures that a port will only permit IP and ARP packets with IP
source ...
... (eos release
4.25.2F)
Support of 400GBASE-ZR with Open Forward Error Correction (O-FEC) (eos release
4.25.2F)
Override a transceiver slot’s maximum power limit (eos release
4.25.2F)
Platform Compatibility ...
... MLAG peer switches are identical platforms and run identical eos images. Running different images/platform may result in a failure to form an association with the MLAG peer or see discrepancy in behavior. ...
...
MACsec Licensing
MACsec encryption is a eos licensed feature. A valid MACsec license must be configured on a switch. MACsec licenses are tied to a switch serial number and the licensee. ...
... command replaces the EOS CLI prompt with an SQLite
prompt.switch# event-monitor interact
sqlite>
This command exits SQLite and returns to the EOS CLI
prompt.sqlite> .quit
switch#
event-monitor ...