Total 20 results found for the keyword of "eos section 24 7 acl route map and prefix list commands"
... and destination
addresses..
acls can also be made dynamic (not persisting in the eos), and the
payload keyword can be used to
turn an acl into a User-Defined Field (UDF) alias for use in other acls. ...
...
show traffic-engineering database
Use the show traffic-engineering database to display the topology used for CSPF computations. Starting from eos Release 4.23.1F, the SRLG group details of a neighbor ...
...
Drop count
Device ID
Egress interface
FCS type
Reserved
TAP Aggregation Extra MPLS Pop (4 to 6 Labels)
Available starting with eos Release 4.23.1F extra MPLS pop for TAP Aggregation ...
... available for other eos applications.
With hardware acceleration, all sFlow processing is done in hardware
using specialized chips, called accelerators. These accelerators
process sampled packets and ...
Sample Configurations
EVPN VXLAN IRB Sample Configuration
In the topology below, we are connecting a Layer 2 site with a Layer 3 site using Layer 3
EVPN (type-5 route). Right side leaves are MLAG ...
...
Starting in Release eos 4.23.1, ingress on inner IP header matching
in MPLS packets is also supported on PBR acls. In order to enable this, the following must
be configured in a user-defined TCAM profile: ...
... is the protocol used to manage
the membership of hosts in multicast groups for IPv6.
RFC 3810 talks about MLDv2 functionality. MLDv2 is the IPv6 counterpart of IGMPv3. Beginning with eos Release 4.25.0F, ...
Protocol Independent
Multicast
Protocol Independent Multicast
(PIM) distributes multicast data using routes gathered by other protocols.
Arista switches support two types of PIM: PIM Sparse Mode ...
... identifier or
a single Customer Edge (CE) to the participating multiple Provider Edge
(PE). The default mode of operation is All-active. Introduced in the
eos 4.26.0F for VxLAN, singe-active is
another ...
... for OSPFv2 adjacencies with DR Other neighbors.
OSPFv2 Multiple Instances Support
eos Release 4.22.1F adds support for multiple OSPFv2 instances to
be configured in the default VRF. OSPFv2 Multiple ...
...
Note: Unlike node segments, anycast segments do not have the ‘N’ flag set described in section 2.1.1.2 of RFC8667.
The following enhancements are available by release:
eos Release 4.22.1F adds support ...
... hop resolution semantics of BGP routes with an ordered list, or profile, of resolution RIB domains (for example, either tunnel or IP domain). This allows eos to direct specific services over the specified ...
... ensure disable-vrf configuration to take effect.
switch(config)# agent SandL3Unicast terminate
SandL3Unicast was terminated
Starting from the eos Release 4.26.0F, /32 prefix length optimization ...
...
eos is optimized to support QoS configuration on the Fabric interfaces on 7250x and 7300 series switches. Configuring QoS on the Fabric interfaces in addition to front panel ports allows user to have ...
... 32-bit
integer used in the candidate path selection
algorithm to select the “active” candidate path.
The default value for preference is
100.
Binding SID (BSID): an optional,
SID.Note: In eos, a BSID ...
... (eos release
4.25.2F)
Support of 400GBASE-ZR with Open Forward Error Correction (O-FEC) (eos release
4.25.2F)
Override a transceiver slot’s maximum power limit (eos release
4.25.2F)
Platform Compatibility ...
... MLAG peer switches are identical platforms and run identical eos images. Running different images/platform may result in a failure to form an association with the MLAG peer or see discrepancy in behavior. ...
... Type Ports
---- ----------- ---- -----
Total Mac Addresses for this criterion: 0
Beginning with eos Release 4.26.0F,
PortSec-Protect enforces a limit on the number of MAC
addresses, ...
...
MACsec Licensing
MACsec encryption is a eos licensed feature. A valid MACsec license must be configured on a switch. MACsec licenses are tied to a switch serial number and the licensee. ...
... CLI.
This chapter includes these sections:
Accessing the eos CLI
Processing Commands
Kernel-based Virtual Machine Commands and Configuration
Switch Platforms
Command Modes
Managing Switch
Configuration ...