Total 20 results found for the keyword of "eos section 9 4 environment commands"
environment commands
environment Control
Configuration commands
environment fan-speed
environment insufficient-fans action
environment overheat action
locator-led
environment Display
commands ...
Precision Time Protocol (PTP) commands
PTP commands
ptp announce interval
ptp announce timeout
ptp delay-mechanism
ptp delay-req interval
ptp domain
ptp enable
ptp forward-v1
ptp hold-ptp-time ...
Switch environment Control
The following sections describe the commands that display temperature, fan, and power supply
status:
environment Control Introduction
environment Control Overview
Configuring ...
... Command: show running-config
! device: switch (DCS-7150S-64-CL, eos-4.13.2F)
ip route 0.0.0.0/0 10.255.255.1
!
environment overheat action ignore
!
!
end
switch#
Insufficient Fans
The switch can ...
...
Drop count
Device ID
Egress interface
FCS type
Reserved
TAP Aggregation Extra MPLS Pop (4 to 6 Labels)
Available starting with eos Release 4.23.1F extra MPLS pop for TAP Aggregation ...
Latency Analyzer (LANZ)
Arista Networks’ Latency
Analyzer (LANZ) is a family of eos features that provide enhanced visibility
into network dynamics, particularly in areas related to the delay packets
experience ...
... leaks in eos or customer user processes.
Process leaks to too many processes or scripts running at one time.
Over configuration of the system requiring more memory than available.
Large number of temporary ...
... is the protocol used to manage
the membership of hosts in multicast groups for IPv6.
RFC 3810 talks about MLDv2 functionality. MLDv2 is the IPv6 counterpart of IGMPv3. Beginning with eos Release 4.25.0F, ...
Audio Video Bridging (AVB)
Arista switches support Audio Video Bridging (AVB) and the associated protocols. This section describes AVB concepts and the implementation of associated protocols.
Topics ...
... identifier or
a single Customer Edge (CE) to the participating multiple Provider Edge
(PE). The default mode of operation is All-active. Introduced in the
eos 4.26.0F for VxLAN, singe-active is
another ...
... distributes operational state information across a set of eos switches to support applications that provide network services. See the CloudVision User Guide, https://www.arista.com/en/support/product-documentation, ...
... for OSPFv2 adjacencies with DR Other neighbors.
OSPFv2 Multiple Instances Support
eos Release 4.22.1F adds support for multiple OSPFv2 instances to
be configured in the default VRF. OSPFv2 Multiple ...
... area and interface levels.
Note: On the same area or interface, eos allows security configuration with either AH or ESP but not both. We can have one area or interface configured with AH and another ...
... hop resolution semantics of BGP routes with an ordered list, or profile, of resolution RIB domains (for example, either tunnel or IP domain). This allows eos to direct specific services over the specified ...
... and destination
addresses..
ACLs can also be made dynamic (not persisting in the eos), and the
payload keyword can be used to
turn an ACL into a User-Defined Field (UDF) alias for use in other ACLs. ...
VRRP and VARP
A virtual IP (VIP) address
is an IP address that does not directly connect to a specific interface.
Inbound packets sent to a Virtual IP address are redirected to a physical
network ...
... VOQ0 are in WRR with a static credit ratio 2:3:6 (higher ratio
implies more credits).
The subinterface inherits the trust mode of the parent interface.
Before eos Release 4.24.2F, shaping is supported ...
Upgrades and Downgrades
This chapter describes the
procedures for upgrading or downgrading the switch software.
This chapter contains these sections:
Upgrade/Downgrade Overview
Smart System Upgrade ...
...
The switch controls access to eos commands by authenticating user identity and verifying user authorization. Authentication, Authorization, and Accounting (AAA) activities are conducted through three ...
... CLI.
This chapter includes these sections:
Accessing the eos CLI
Processing commands
Kernel-based Virtual Machine commands and Configuration
Switch Platforms
Command Modes
Managing Switch
Configuration ...