Date: November 18th, 2015

Revision Date Changes
1.0 November 18th, 2015 Public release
1.1 November 18th, 2015 Updated to include CVE number and bug ID
 

Arista EOS Remote Privilege Escalation Vulnerability - CVE-2015-8236

This advisory is to document a security vulnerability identified by Arista Networks that affects EOS. Affected EOS releases are listed in Table-1 below. This issue is a privilege escalation vulnerability that could allow a remote attacker with IP connectivity to the management plane of the switch to run arbitrary code as a privileged user. This includes getting root level access to the bash shell on the switch. It is not required for the attacker to have credentials for a user account on the switch. All methods of management plane access are exposed.

NOTE: This vulnerability was identified internally by Arista Networks and there have been no external reports of an exploit, as of the date of this notice.

Recommended Action: For switches running any affected EOS version, the immediate recommendation is to install a non-disruptive patch or to upgrade to a remediated version of EOS. Either step will prevent any exploit.

A single patch for this issue is available for EOS versions 4.5.0 and later via the URL below and this patch can be installed non-disruptively. Applying this patch serves as a permanent resolution to this issue. Instructions to install the patch is documented in this advisory.

Table-2 below contains the list of EOS versions that contain the security fix.

Affected software releases: All EOS releases shipped prior to the date of this release are affected. The following table only lists the affected EOS versions from the supported release trains. Release trains older than 4.11, such as 4.10, 4.9, 4.8, 4.7, 4.6, 4.5 and older, are affected as well.

4.15 4.14 4.13 4.12 Older release trains
4.15.0F
  • 4.15.0FX
  • 4.15.0FXA
  • 4.15.0FX1
4.15.1F
  • 4.15.1FXB
  • 4.15.1FX-7060X
  • 4.15.1FX-7260QX
4.15.2F
4.14.0F
4.14.1F
4.14.2F
4.14.3F
4.14.3.1F
4.14.4F
4.14.4.1F
4.14.4.2F
4.14.5F
  • 4.14.5FX
  • 4.14.5FX.1
  • 4.14.5FX.2
  • 4.14.5FX.3
  • 4.14.5FX.4
  • 4.14.5.1F-SSU
4.14.6M
4.14.7M
4.14.7.1M
4.14.8M
4.14.8.1M
4.14.9M
4.13.1.1F
4.13.2.1F
4.13.3.1F
4.13.4.1F
4.13.5F
4.13.5.1F
4.13.6F
4.13.7M
4.13.7.2M
4.13.7.3M
4.13.8M
4.13.9M
4.13.9.1M
4.13.10M
4.13.11M
4.13.12M
4.13.13M
4.12.5.2
4.12.6.1
4.12.7.1
4.12.8
4.12.8.1
4.12.9
4.12.10
All releases in 4.11
All releases in 4.10
All releases in 4.9
All releases in 4.8
All releases in 4.7
All releases in 4.6
All releases in 4.5
All release trains older than 4.5

Table-1: Affected EOS releases

Affected platforms: All Arista platforms

Resolution:Bug 138716 tracks this vulnerability. The following table lists the releases that contain the fix for the vulnerability. These releases are available on the software downloads page.

EOS-4.15 EOS-4.14 EOS-4.13 EOS-4.12 EOS-4.11
4.15.0FX1.1
4.15.0FXA.1
4.15.1FXB.1
4.15.1FX-7060X.1
4.15.2.1F or later
4.14.5FX.5
4.14.5.1F-SSU.1
4.14.9.1M or later
4.13.14M or later 4.12.11 or later 4.11.12 or later

Table-2: EOS releases with security fix

Patch file download URL: secAdvisory0015.swix

MD5SUM: 12a669428dc3ac8697dffabed31c18f9

SHA512SUM: 4c98ba78dfa93f180e0f826d0d82f41219125dcccdf37595b65277193492fa9aa5ec13b79eec25765a8375b58d8594879e9d369175e9d6f9c3fd092392d0aee8

NOTE:

  • The patch is applicable only to EOS versions starting at 4.5.0 and later
  • Installing the patch is non-disruptive to switch operation or traffic flowing through the switch
  • A reload of the switch is not required for the patch to take effect

Instructions to install the patch

  1. Download the patch file and copy the file to the extension partition of the switch using one of the supported file transfer protocols:
    switch#copy scp://10.10.0.1/secAdvisory0015.swix extension:
    switch#verify /sha512 extension:secAdvisory0015.swix

    Verify that the checksum value returned by the above command matches the provided SHA512 checksum for the file
    On modular systems with dual supervisors, download the file to the extension partition of the active supervisor and copy it to the standby supervisor using the following two commands:
    switch(s1)(config)#copy extension:secAdvisory0015.swix supervisor-peer:/mnt/flash/
    switch(s2-standby)#copy flash:secAdvisory0015.swix extension:
  2. Install the patch using the extension command. The patch takes effect immediately at the time of installation.
    switch#extension secAdvisory0015.swix 

    On modular systems with dual supervisors, the patch has to be installed on the active and standby supervisors:
    switch(s1)#extension secAdvisory0015.swix 
    switch(s2-standby)#extension secAdvisory0015.swix

    If eAPI is enabled, the eAPI agent or the uwsgi service will restart after the patch has been installed. One of following messages will be logged as a result:
    ProcMgr-worker: %PROCMGR-6-PROCESS_RESTART: Restarting 'CapiApp' immediately 
    SuperServer: %SYS-4-RESTART_SERVICE: Service uwsgi is not running. Attempting to restart it.
  3. Verify that the patch is installed using the following commands:
    switch#show extensions 
    Name Version/Release Status extension
    ----------------- ------------------------- ------ ---------
    secAdvisory0015.swix 1.0.0/SA15 A, I 1
    A: available | NA: not available | I: installed | NI: not installed | F: forced
    switch#show ver detail  | grep SA15 
    secAdvisory0015 1.0.0 SA15
  4. Make the patch persistent across reloads. This ensures that the patch is installed as part of the boot-sequence. The patch will not install on EOS versions with the security fix.
    switch#copy installed-extensions boot-extensions 
    switch#show boot-extensions
    secAdvisory0015.swix

    For dual supervisor systems run the above copy command on both active and standby supervisors:
    switch(s1)#copy installed-extensions boot-extensions 
    switch(s2-standby)#copy installed-extensions to boot-extensions

Instructions to uninstall the patch:

  1. Uninstall the patch using the following command:
    switch#no extension secAdvisory0015.swix

    On modular systems with dual supervisors, the patch has to be uninstalled on the active and standby supervisors:
    switch(s1)#no extension secAdvisory0015.swix 
    switch(s2-standby)#no extension secAdvisory0015.swix

    The output of ‘show extensions’ will reflect the status of the patch as ‘NI: Not installed’
    switch#show extension 
    Name Version/Release Status extension
    ----------------- ------------------------- ------ ---------
    secAdvisory0015.swix 1.0.0/SA15 A, NI 1
    A: available | NA: not available | I: installed | NI: not installed | F: forced
    NOTE: Once the extension has been uninstalled, the switch is no longer protected against the vulnerability.
  2. To make this change persistent across switch reloads, run the following command to remove the patch from boot-extensions:
    switch#copy installed-extensions boot-extensions 
    switch#show boot-extensions

    For dual supervisor systems run the above copy command on both active and standby supervisors:
    switch(s1)#copy installed-extensions boot-extensions 
    switch(s2-standby)#copy installed-extensions boot-extensions

Upgrade considerations:

  • It is recommended to uninstall the patch before upgrading to a remediated version of EOS. To uninstall the patch, follow the instructions above.
  • When upgrading from EOS versions older than 4.11.0, please refer to the release notes for considerations around memory and software support

For More Information:
If you require further assistance, or if you have any further questions regarding this security notice, please contact the Arista Networks Technical Assistance Center (TAC) by one of the following methods:

Open a Service Request:
By email: 该邮件地址已受到反垃圾邮件插件保护。要显示它需要在浏览器中启用 JavaScript。
By telephone: 408-547-5502
866-476-0000