- Written by Lucas Frere
- Posted on 11月 17, 2023
- Updated on 11月 4, 2025
- 9908 Views
Slice reservation can be used to solve TCAM resources limitations due to suboptimal group order in the TCAM because of the FCFS (First come first serve) nature of the TCAM. The user will be able to reserve a certain amount of entries in the TCAM for a specific feature. The configuration happens through a new keyword in feature mode when configuring a TCAM profile.
- Written by Will Li
- Posted on 4月 18, 2022
- Updated on 7月 27, 2026
- 12018 Views
The ‘redirect’ action used in TCAM profile has lower priority than system rules, if packets match both TCAM rule using ‘redirect’ action and system rules. Hence ‘redirect’ action does not take effect on these packets. This improvement allows ‘redirect’ action in TCAM profile to override system rules, so that the aforementioned packets will always be redirected even if they match system rules.
- Written by John Schimmel
- Posted on 3月 13, 2026
- Updated on 3月 13, 2026
- 1057 Views
The Dapper action, derived from Brown University research, identifies TCP session issues by measuring specific connection attributes. This analysis determines whether performance degradation stems from the client, server, or network devices.
- Written by Robert Ling
- Posted on 5月 2, 2025
- Updated on 5月 5, 2025
- 3674 Views
DMF 8.7.0 introduces an updated dashboard for analyzing TCP Flows from Dapper. The DMF Analytics Node (AN) displays TCP Window, Network Loss, Zero Window, RTT vs Sender Reaction Time for flows or select Flow from TCP Health Flows.
- Written by Ganesh Priyatham Palivela
- Posted on 4月 1, 2026
- Updated on 4月 1, 2026
- 896 Views
Temporal Tail Drop Thresholds enables the configuration of interface TX queue tail drops thresholds in units of time. The system dynamically computes the maximum allowable queue occupancy by considering the current interface speed and the Weighted Round Robin (WRR) bandwidth allocation. This feature simplifies configuration in environments with mixed link speeds. The calculated threshold represents the maximum bytes queued to hold packets for the specified duration.
- Written by Vipul Shah
- Posted on 8月 27, 2019
- Updated on 11月 16, 2026
- 11250 Views
BGP routing information often contains more than one path to the same destination network. The BGP best-path selection algorithm determines which of these paths should be considered as the best path to that network
- Written by Nikhil Goyal
- Posted on 12月 20, 2024
- Updated on 12月 20, 2024
- 5132 Views
Topology Independent Fast Reroute, or TI-LFA, uses OSPF SR to build loop-free alternate paths along the post-convergence path. These loop-free alternates provide fast convergence.
- Written by Dylan Walsh
- Posted on 4月 17, 2026
- Updated on 4月 17, 2026
- 918 Views
As of EOS-4.36.0F, a configurable user session timeout is supported for console, SSH, and telnet management sessions. This feature closes the user session (interactive) once the specified duration has been reached, regardless of user activity and independent of any configured idle-timeout. Upon session termination, a system message is generated to indicate the session’s closure. This feature is disabled by default.
- Written by Niall Sauvage
- Posted on 7月 1, 2026
- Updated on 9月 25, 2026
- 525 Views
The Timing Regeneration Filter (TRF) is a part of the Clock and Data Recovery component of the CRT50216 external PHY from Credo. It has a parameter, known as the bandwidth, which adjusts how the CRT50216 adjusts to frequency changes in the incoming signal from the peer.
- Written by Baptiste Covolato
- Posted on 1月 13, 2026
- Updated on 1月 13, 2026
- 2006 Views
Secure boot is a security feature available in Aboot (Arista bootloader) that verifies the cryptographic signature of the EOS SWI (software image) before it is booted. Aboot embeds certificates that allow it to recognize and validate official EOS releases from Arista. If the signature verification is successful, the secure boot check passes and Aboot proceeds to boot the SWI. If the signature verification fails, the boot is aborted.
- Written by Benjamin Ye
- Posted on 6月 26, 2026
- Updated on 6月 26, 2026
- 543 Views
The tone generation feature enables switches to produce tones for fiber optic identification. This can produce 270Hz tones that standard fiber optic identifier devices can detect. The feature generates tones using SFP transceivers by toggling transceiver transmit disable at a configurable frequency. When enabled, this feature will disrupt the link and traffic on the interface.
- Written by Ilia Lebedev
- Posted on 10月 16, 2026
- Updated on 10月 16, 2026
- 213 Views
4.36.0F TPM-anchored keys are a security feature that allow a compatible EOS switch to use its trusted platform module (TPM, a dedicated hardware component of the switch’s CPU board, or of a modular switch’s supervisor) to configure and use cryptographic keys for certain operations.
- Written by Vikas Saini
- Posted on 4月 30, 2025
- Updated on 4月 30, 2025
- 2756 Views
Before release 4.34.0F traffic in Port Mode PW was always classified based on COS-To-TC global map irrespective of trust mode. This feature allows users to classify traffic in accordance with trust mode, default CoS and default DSCP of the interface.
- Written by Kumaran Narayanan
- Posted on 10月 24, 2024
- Updated on 6月 6, 2025
- 7027 Views
This feature enables applying traffic policies on incoming traffic and redirecting the traffic to a nexthop other than the one the routing logic would choose. This essentially overrides the routing logic decision. If there is no rule matching the packet, the packet is sent to the routing logic to be routed.
- Written by Travis Hammond
- Posted on 3月 31, 2017
- Updated on 7月 21, 2023
- 13584 Views
This article describes the TAP Aggregation User Defined Fields feature. The purpose of the User Defined
- Written by Radu Handolescu
- Posted on 9月 29, 2026
- Updated on 9月 30, 2026
- 323 Views
Historically EOS transceiver-related configurations have been applied on a per-interface or per-slot basis, however this approach is inefficient in applying a configuration that is relevant to a group of transceiver modules determined by certain criteria.
To address such use cases, the concept of “transceiver matching rules” is being introduced.
- Written by Vincent He
- Posted on 4月 30, 2025
- Updated on 7月 2, 2025
- 3678 Views
This feature introduces a slot level CLI command for SFP transceivers. When configured, EOS will only manage the transceiver via the low speed hardware pins. The command is intended to be used in situations where SMBUS communication to access transceiver EEPROM is not reliable, which would normally lead to EOS disabling the port. Enabling this feature ignores any EEPROM dependent functionality and only turns on the laser, which may allow the link to come up when the default factory settings for both ends of the link are compatible.
- Written by Lavanya Conjeevaram
- Posted on 2月 8, 2017
- Updated on 2月 4, 2022
- 11272 Views
This feature adds support for viewing the Digital Optical Monitoring (DOM) parameters for the optics that support
- Written by Rajeev Menon
- Posted on 3月 18, 2025
- Updated on 7月 17, 2025
- 3890 Views
The feature introduces a CLI command for transceiver reinitialization, simulating a physical removal and reinsertion of the transceiver. This is a great feature for remote troubleshooting, when physical access is not possible or convenient. To configure, issue the CLI command "transceiver reinitialize slot" in exec mode. The command takes effect immediately, toggles the reset pin and initiates a transceiver initialization sequence.
- Written by Rajeev Menon
- Posted on 9月 30, 2019
- Updated on 7月 9, 2025
- 12114 Views
This feature provides the capability to configure transceiver SERDES electrical tuning parameters. The ability to
- Written by Abhishek Kumar
- Posted on 4月 30, 2025
- Updated on 4月 30, 2025
- 2867 Views
When the system exhausts ECMP resources, the Transient ECMP feature enables route programming through a single available next-hop from the original ECMP route. Once the system can program the full ECMP route, the transient ECMP route is removed after successfully installing the ECMP route.
- Written by Kiran Poola
- Posted on 4月 24, 2025
- Updated on 4月 29, 2025
- 5852 Views
The following describes LAG hashing for L2GRE and VXLAN transit traffic on Arista 7050X4 platforms: For L2GRE transit traffic, LAG hashing uses only the encapsulated (inner) packet header fields. There is no option to use underlay (outer) packet header fields. When the encapsulated packet is IP, the system uses the IP parameters configured with hash ipv4 or hash ipv6 for hashing.
- Written by Nick Wang
- Posted on 4月 24, 2025
- Updated on 4月 29, 2025
- 6019 Views
UDF is an important DMF feature that matches customized fields in packet payloads for network traffic filtering on the Arista 7050X4 Series. Only supports IPv4 traffic UDF filtering, Maximum UDFs per rule: 6 UDFs.
- Written by Tony Truong
- Posted on 9月 30, 2015
- Updated on 10月 1, 2015
- 10200 Views
As of EOS 4.15.2F, the support for the tuning of tunable DWDM 10G SFP+ transceivers (10GBASE DWDM) is added.
- Written by Noah Rinkle
- Posted on 7月 21, 2026
- Updated on 7月 21, 2026
- 505 Views
The tunnel historical health monitoring dashboard provides the historical status of all the VXLAN tunnels formed by the selected Access Point at a location. The historical data helps to narrow down the affected time period for the tunnel and isolate a specific window for troubleshooting.
- Written by Robert Ling
- Posted on 5月 5, 2025
- Updated on 5月 5, 2025
- 3549 Views
DMF 8.7.0 introduces an updated dashboard for viewing tunnel traffic. The widgets display traffic distribution by tunnel type using sFlow traffic categorized by a combination of Ethernet Type, Protocol, and L4 ports. Recognized tunnels include:
- Written by Shilpa Santhanam
- Posted on 1月 17, 2019
- Updated on 3月 26, 2025
- 10965 Views
4.21.3F introduces support for the feature on the platforms listed below. The TOI describing the feature support on different versions/platforms is available here.
- Written by Liviu Ivan
- Posted on 1月 6, 2026
- Updated on 1月 13, 2026
- 1576 Views
TX queue precision shaping allows improving accuracy of observed shape rates on interfaces relative to configured values, in particular when the configured rate is low.
- Written by Abhishek S
- Posted on 4月 21, 2026
- Updated on 4月 21, 2026
- 726 Views
Tx-Queues are usually assigned to subinterfaces only when explicit shaping or scheduling is configured. Without this feature, unshaped or unscheduled subinterfaces might continue to use the parent interface's Tx-Queues. This capability enables the allocation of a set of Tx-Queues to the subinterface, with the Tx-Queues operating at the maximum shaping rate derived from the parent interface. This feature is only supported in conjunction with Priority Aware Subinterface Scheduling.
- Written by Prathamesh Timse
- Posted on 11月 22, 2017
- Updated on 11月 22, 2017
- 10066 Views
The BGP labeled unicast (LU) RFC is used to advertise BGP routes with a stack of MPLS labels, thereby allowing
- Written by Kaushik Kumar Ram
- Posted on 9月 30, 2015
- Updated on 2月 7, 2022
- 11547 Views
Trident2 is a Switch on Chip (SoC) single chip with support for up to 1280Gbps of forwarding capacity (oversubscribed
- Written by Mihyar Baroudi
- Posted on 2月 1, 2016
- Updated on 2月 7, 2022
- 11443 Views
This feature provides a configuration option to disable egress IPv4 RACL sharing allowing for uRPF to be configured.
- Written by Dhruba Jyoti Pokhrel
- Posted on 3月 23, 2026
- Updated on 3月 23, 2026
- 992 Views
When a client requests IP addresses from the DHCP server, the DHCP server typically broadcasts the message to the connected Access Points (AP) and other devices. This results in flooding of the AP and the network.
- Written by Lavanya Conjeevaram
- Posted on 9月 11, 2017
- Updated on 7月 2, 2025
- 15354 Views
Unidirectional links is a feature that configures an Ethernet interface transmit and receive paths to be independent. Specifically, the transmit path can be up or down independent of the receive path being up or down.
- Written by Olufemi Komolafe
- Posted on 10月 22, 2025
- Updated on 11月 3, 2025
- 3012 Views
At its most basic level, as shown in Figure 1, the packet forwarding pipeline for a switch with an application-specific integrated circuit (ASIC) typically consists of ingress pipelines and egress pipelines, a memory management unit for storing and transmitting packets and metadata between the pipelines, and a path to punt packets and receive instructions from the central processing unit (CPU).
- Written by Gowtham Rameshkumar
- Posted on 9月 15, 2023
- Updated on 4月 21, 2026
- 9331 Views
The Unified Forwarding Table (UFT) is a group of memories that is shared between Layer2 and Layer3 lookup tables with capabilities for variable partitions. Rather than separate Layer2 and Layer3 lookup tables of fixed size, the UFT may be partitioned to support user-requested combinations of Layer2 and Layer3 lookup tables of varying sizes. The new UFT partitioning CLI has capabilities to reconfigure individual forwarding table scales (Layer2, Layer3 Unicast, Layer3 Multicast) according to the user’s input. The CLI provides an interface for granular control of the underlying UFT resources.
- Written by Prachi Modi
- Posted on 1月 16, 2023
- Updated on 1月 16, 2023
- 9651 Views
With the 13.0 release, CloudVision Cognitive Unified Edge (CV-CUE) lets you configure Unique PSK (UPSK) for client authentication. UPSKs allow users to connect to the same SSID using a unique PSK which is user specific. UPSK provides added security as compared to single PSK because single PSKs are easily compromised.
- Written by Prachi Modi
- Posted on 7月 7, 2023
- Updated on 7月 7, 2023
- 9065 Views
With the 15.0 release, CloudVision Cognitive Unified Edge (CV-CUE) introduces the following enhancements to the Unique-PSK(UPSK) workflow:
- Written by Eudean Sun
- Posted on 9月 2, 2025
- Updated on 9月 2, 2025
- 3634 Views
Arista currently posts separate EOS images for different CPU architectures: i686 (EOS.swi), x86_64 (EOS64.swi), and aarch64-based (EOSarm.swi, starting with EOS-4.35.0F). The universal SWI (EOSuni.swi) is a single file containing support for all CPU architectures, meant to simplify image management and provisioning. The universal SWI will be posted in addition to the existing architecture-specific SWIs and is not meant to fully replace them.
- Written by Preyas Hathi
- Posted on 6月 2, 2022
- Updated on 6月 2, 2022
- 10642 Views
With the 12.0 release, you can check for available upgrades and upgrade your server to the latest version of CloudVision Cognitive Unified Edge (CV-CUE). Only a Superuser can initiate a server upgrade.
- Written by Ayaka Koshibe
- Posted on 12月 10, 2024
- Updated on 12月 10, 2024
- 6095 Views
CVA 6.x may be upgraded to CVA 7.0 with an upgrade launcher. The launcher is an interactive executable that is run on the CVA system that is to be upgraded, and performs several functions Staging of an appropriate upgrade image for autoinstall
- Written by Cian Levy
- Posted on 8月 29, 2025
- Updated on 8月 29, 2025
- 2924 Views
CVA 6.x may be upgraded to CVA 7.1 with an upgrade launcher. The launcher is an interactive executable that is run on the CVA system that is to be upgraded, and performs several functions
- Written by Dhruba Jyoti Pokhrel
- Posted on 1月 17, 2024
- Updated on 1月 17, 2024
- 7979 Views
With the 16.0 release, you can authenticate edge devices from a centrally managed network access control server using the 802.1X authentication. As a network administrator, you want to authenticate the access points (APs), before the APs connect to the network. To enable the authentication, you need to first configure the uplink port on the AP using CV-CUE.
- Written by Noah Rinkle
- Posted on 7月 21, 2026
- Updated on 7月 21, 2026
- 517 Views
Upload and manage access point (AP) images directly from the AP details page. It helps you easily identify the AP in a large deployment. Images are compressed before you upload them, and they are automatically compressed on the client device to optimize storage and network usage. It has a carousel viewer for browsing uploaded photos and supports up to four photos per AP.
- Written by Poorna Pushkala Balasubramanian
- Posted on 11月 22, 2017
- Updated on 8月 11, 2023
- 9760 Views
This feature adds the capability to import as path access-list from a URL, in release 4.20.1F. The file specified by the URL can contain one or more as-path access-list entries. All the entries that are in the file are added to the as-path access-list being configured. This feature gives the advantage of using one EOS CLI command to configure many as-path access-list entries, instead of adding each one of them line by line in the CLI.
- Written by Wenyi Cheng
- Posted on 2月 8, 2017
- Updated on 2月 4, 2022
- 13584 Views
Role based access control (RBAC) is an approach to regulating access to network resources based on the roles of
- Written by Kinjal Bhattacharyya
- Posted on 3月 18, 2026
- Updated on 3月 18, 2026
- 967 Views
The Command-API (CAPI) client on the Controller utilizes port 443 for EOS connectivity.
- Written by Mike Nelson
- Posted on 4月 10, 2015
- Updated on 9月 18, 2024
- 12416 Views
Packets which exceed the L2 Maximum Transmission unit (MTU) in EOS are dropped. The value of the L2 MTU is configurable for each Ethernet or Port-channel interface.
- Written by Anirudh Ramesh Iyer
- Posted on 5月 5, 2021
- Updated on 4月 22, 2026
- 29932 Views
This article describes how to customize TCAM ( Ternary Content Addressable Memory ) lookup for each feature which uses TCAM. The lookup is composed of fields, in the packet header / forwarding chip pipeline decisions, that are of interest to a feature. Size of the lookup determines the number of banks to be used by a feature. Traditionally, any feature uses a predefined TCAM lookup.
- Written by Peter Thompson
- Posted on 3月 21, 2025
- Updated on 9月 25, 2026
- 4096 Views
User-defined TPIDs allow an arbitrary TPID (Tag Protocol Identifier) to be used with a FlexEncap specification. A TPID is used in Ethernet frames to identify the encapsulation protocol, where standard values like 0x8100 (for IEEE 802.1q VLAN tagging) and 0x88a8 (for IEEE 802.1ad Q-in-Q) are commonly used. However, some network equipment may use non-standard or legacy values such as 0x9100. This feature allows FlexEncap subinterfaces to be configured with an arbitrary TPID to allow interfacing with networking equipment that uses values besides 0x8100 and 0x88a8.
