Overview

This guide is intended for network professionals who need to install the Arista 5000 Series Enterprise WAN Routers.

The following topics are covered in this section:

Scope

This section lists the routers that are described in this guide:

  • Arista 5310 Enterprise WAN Router

  • Arista 5510 Enterprise WAN Router

CAUTION: Only qualified or trained personnel should install, service, or replace this equipment.

Seul le personnel qualifié doit installer, service, ou remplacer cet équipement.

Receiving and Inspecting the Equipment

 

Upon receiving the router, inspect the packaging and record any external damage. If you suspect any part of the shipment is damaged, retain the packing material; the carrier might need it to inspect.

If the packaging was not damaged during transit, unpack each box carefully. Ensure that you do not discard any accessories that may be packed in the same box as the router.

Review the packing list that comes with the router to ensure you have received all the items listed. Refer to the Parts List to verify that all components are included.

Installation Process

This section describes the steps required to install and use the router in a Data Center environment:

  1. Select and prepare the installation site. (Site Selection)
  2. Assemble the installation tools listed. (Tools and Parts Required for Installation)
  3. Attach the mounting brackets and install the router in an equipment rack. (Rack Mounting the Router)
  4. Connect the router to the power source, console cables, and management network. (Cable the Router)
  5. Configure the router. (Configuring the Router)

Safety Information

Refer to the Arista Networks document Safety Information and Translated Safety Warnings available at https://www.arista.com/en/support/product-documentation.

Important: Class 1 laser product: This product has provisions to install Class 1 laser transceivers which provide optical coupling to the communication network. Once a Class 1 laser product is installed, the equipment is a Class 1 laser product (Appareil à Laser de Classe 1). The customer is responsible for selecting and installing the Class 1 laser transceiver and for ensuring that the Class 1 AEL (allowable emission limit) per EN/IEC 60825, CSA E60825-1, and Code of Federal Regulations 21 CFR 1040 is not exceeded after the laser transceiver has been installed. Do not install laser products whose class rating is greater than 1. Refer to all safety instructions that accompanied the transceiver prior to installation. Only Class 1 laser devices certified for use in the country of installation by the cognizant agencies are to be utilized in this product. Ultimate disposal of this product should be in accordance with all applicable laws and regulations.

Produit laser de classe 1: Ce produit a des dispositions pour installer des émetteurs-récepteurs de laser de classe 1 qui offre de couplage au réseau de communication optique. Une fois un produit laser de classe 1 est installé, l'équipement est un produit laser de classe 1 (Appareil à laser de Classe 1). Le client est responsable pour sélectionner et installer l'émetteur/récepteur de laser de classe 1 et pour assurer que la classe 1 AEL (limite d'émission admissible) par EN/IEC 6-825, CSA E60825-1, et Code des règlements fédéraux 21 CFR 1040 ne soit pas dépassée après avoir installé l'émetteur/récepteur de laser. Ne pas installer des appareils à laser dont la cote de classe est supérieure à 1.Voir toutes les consignes de sécurité qui ont accompagné l'émetteur-récepteur avant l'installation. Seuls appareils laser de classe 1 certifiés pour une utilisation dans le pays d’installation par l’organisme compétent doivent être utilisées dans ce produit.

 

Important: DO NOT open the case of the router. There are NO user serviceable parts inside. Entrust any repair to a qualified technician.

N’ouvrez PAS le boîtier du routeur. Il n’y a AUCUNE pièce réparable par l’utilisateur à l’intérieur. Confiez toute réparation à un technicien qualifié.

Obtaining Technical Assistance

Any customer, partner, reseller, or distributor holding a valid Arista Service Contract can obtain technical support in any of the following ways:

  • Email: 이 이메일 주소가 스팸봇으로부터 보호됩니다. 확인하려면 자바스크립트 활성화가 필요합니다.

    Include a detailed description of the problem and the “show tech-support” output.

     

     

  • Web: https://www.arista.com/en/support

    A support case may be created through the support portal on our website. You may also download the most current software and documentation, as well as view FAQs, Knowledge Base articles, Security Advisories, and Field Notices.

     

     

  • Phone: +1 866-476-0000 or +1 408-547-5502

Specifications

This section lists the specifications of the Arista 5000 Series Enterprise WAN Routers.

Table 1. Dimensions and Weights
Router Size (W x H x D) Weight
AWE-5310-2F-FLX 17.32 x 1.71 x 16.92 inches

(440 x 43.5 x 430 mm)

 20.5 lbs

(9.3 kg)
AWE-5510-2F-FLX 17.32 x 3.46 x 20.47 inches

(440 x 88 x 520 mm)

 29.98 lbs

(13.6 kg)

 

 

Table 2. Operating and Storage Temperature
Router Operating Temperature Storage Temperature Operating Altitude Relative Humidity
AWE-5310-2F-FLX 32° to 104°F

(0° to 40°C)

 -13° to 158°F

(-25° to 70°C)

 0 to 10,000 feet

(0 to 3,000 meters)

 5 to 95%

(non-condensing)
AWE-5510-2F-FLX 32° to 104°F

(0° to 40°C)

 -13° to 158°F

(-25° to 70°C)

 0 to 10,000 feet

(0 to 3,000 meters)

 5 to 95%

(non-condensing)

 

 

Table 3. Power Input
Router Power Source Input Power Rating
AWE-5310-2F-FLX Power Input (AC Power) 100-240VAC, 8-4A, 50/60 Hz
AWE-5510-2F-FLX Power Input (AC Power) 100-240VAC, 10-5A, 50/60 Hz

 

 

Router Power Draw (Typical/Maximum) Supported Power Supply
AWE-5310-2F-FLX 100W/500W AWE-5300-550-A-PS/PWR-00619-01
AWE-5510-2F-FLX 200W/750W AWE-5500-800-A-PS/PWR-00618-01

 

 

Table 5. System Configurations
Router Airflow Power Supply Fan Fan Type
AWE-5310-2F-FLX Front to rear 2 4+1 Fixed/built-in
AWE-5510-2F-FLX Front to rear 2 3+1 AWE-5500-A-FAN