Total 50 results found for the keyword of "eos routing information protocol"
routing information protocol (RIP)
This chapter contains the following sections.
RIP Conceptual
Overview
Running RIP
on the Switch
Configuring RIP on Multiple VRFs
RIP Commands
RIP Conceptual ...
routing protocols
The routing protocols chapter contains the following sections:
routing information protocol (RIP)
Open Shortest Path First – Version 2
Open Shortest Path First – Version 3
IS-IS ...
EVPN VXLAN Single-Gateway Centralized routing
In a traditional EVPN VXLAN centralized anycast gateway deployment, multiple L3 VTEPs
serve the role of the centralized anycast gateway. In order for ...
Integrated routing and Bridging
In traditional data center design, inter-subnet forwarding is provided by a centralized
router, where traffic traverses across the network to a centralized routing ...
protocol Independent
Multicast
protocol Independent Multicast
(PIM) distributes multicast data using routes gathered by other protocols.
Arista switches support two types of PIM: PIM Sparse Mode ...
Multicast Source Discovery protocol (MSDP)
Multicast Source Discovery
protocol (MSDP) describes a topology that connects multiple IPv4 protocol
Independent Multicast Sparse-Mode (PIM-SM) domains. ...
... hop resolution semantics of BGP routes with an ordered list, or profile, of resolution RIB domains (for example, either tunnel or IP domain). This allows eos to direct specific services over the specified ...
... displays
information about the active flows maintained in the eos.
Command Mode
EXEC
Command Syntax
show flow tracking sampled flow-table [
detail | dst-ip |
dst-port | group |
interface | protocol ...
... rates also decrease the amount of processing
time available for other eos applications.
With hardware acceleration, all sFlow processing is done in hardware
using specialized chips, called accelerators. ...
VM Tracer
This chapter describes VM Tracer configuration and usage and contains these sections:
VM Tracer Introduction
VM Tracer Description
VM Tracer Configuration Procedures
VM Tracer Commands ...
... be enabled or disabled on the fly
without impacting regular packet forwarding functionality.
AVA Switch Sensor Extension
AVA switch sensor extends eos telemetry for network threat detection. The FlowWatcher
agent ...
RSVP-TE LSR
RSVP-TE applies the Resource Reservation protocol (RSVP) for Traffic Engineering (TE), that is, to distribute MPLS labels for steering traffic and reserving bandwidth.
The eos implementation ...
LDP Pseudowire
LDP pseudowire provides support for emulating Ethernet connections over a
Multiprotocol Label Switching (MPLS) network, and controlled using the extension of the MPLS
Label Distribution ...
...
show traffic-engineering database
Use the show traffic-engineering database to display the topology used for CSPF computations. Starting from eos Release 4.23.1F, the SRLG group details of a neighbor ...
...
Drop count
Device ID
Egress interface
FCS type
Reserved
TAP Aggregation Extra MPLS Pop (4 to 6 Labels)
Available starting with eos Release 4.23.1F extra MPLS pop for TAP Aggregation ...
Latency Analyzer (LANZ)
Arista Networks’ Latency
Analyzer (LANZ) is a family of eos features that provide enhanced visibility
into network dynamics, particularly in areas related to the delay packets
experience ...
VCS to EVPN Hitless Migration
VCS to EVPN Hitless Migration enables support for migrating from only using VCS as the control plane to only using EVPN as a control plane in a hitless manner with respect ...
Sample Configurations
EVPN VXLAN IRB Sample Configuration
In the topology below, we are connecting a Layer 2 site with a Layer 3 site using Layer 3
EVPN (type-5 route). Right side leaves are MLAG ...
EVPN and VCS Commands
Global Configuration Mode
router
general
Router BGP Configuration Mode
next-hop
resolution disabled
redistribute
service vxlan
route-target
route-target
export
route-target ...
...
Starting in Release eos 4.23.1, ingress on inner IP header matching
in MPLS packets is also supported on PBR ACLs. In order to enable this, the following must
be configured in a user-defined TCAM profile: ...