Total 25 results found for the keyword of "eos multicast source discovery protocol"
...
Configuring MSDP TCP Authentication
eos supports multicast source discovery protocol (MSDP) peering over TCP. Previously, MSDP sessions in eos did not provide a built-in TCP-level authentication ...
... interface vlan 8
switch(config-if-Vl8)# pim ipv4 sparse-mode
switch(config-if-Vl8)#
Enabling PIM IPv6 Sparse Mode
By default, eos disables IPv6 PIM disabled on an interface. The pim ipv6 sparse-mode ...
EVPN multicast VRF Leaking
Overview
EVPN multicast virtual routing and forwarding (VRF) Leaking forwards multicast
traffic from a sender in a tenant or external domain (VRF) to a different domain
(VRF) ...
... Beginning with eos Release 4.25.0F, MLDv2 snooping is supported on
MLAG deployments.
Limitations
The extraneous “Switch” interface should be ignored in show mld
snooping counters and show mld snooping
counters ...
multicast
IP multicast is the transmission of data packets to multiple hosts through a common IP
address. Topics covered in this section include:
multicast Architecture
IGMP and IGMP
Snooping
protocol ...
... allows eos to direct specific services over the specified RIB domains, overriding the default behavior. Further, this feature, through the use of user-defined tunnel RIBs, empowers an administrator to ...
... Convergence
Configuring BPDU Transmissions
Version Configuration and Instance
Creation
The switch supports three STP versions and switchport backup interface pairs. eos supports
disabling STP ...
VM Tracer
This section describes VM Tracer configuration and usage and contains these sections:
Introducing VM Tracer
VM Tracer Description
VM Tracer Configuration Procedures
VM Tracer ...
... eos sends hello messages to all known neighbors every
10 seconds. If the switch does not receive
hello responses from a neighbor for 4*10=40 seconds, the switch considers
communication with the neighbor ...
Configuring RSVP-TE P2MP Tunnels
RSVP-TE P2MP Tunnels adds support for Point-to-Multipoint (P2MP) tunnels to be used in
multicast Virtual Private Network (MVPN).
There are two major parts to the ...
EVPN and VCS Commands
Global Configuration Mode
router
general
Router BGP Configuration Mode
next-hop
resolution disabled
redistribute
service vxlan
route-target
route-target
export
route-target ...
... Note: All
connected interfaces are advertised as bound. However, eos currently advertised
labels for /32 addresses, and FEC filter is configured to install only
x.x.x.200/32
prefixes. North Edge.17:51:17# ...
VCS to EVPN Hitless Migration
VCS to EVPN Hitless Migration enables support for migrating from only using VCS as
the control plane to only using EVPN as a control plane in a hitless manner concerning ...
...
eos adds a new parameter in the output, evpn
prefix
detail to display the ATTR_SET, code
128
attributes.switch# show bgp evpn
BGP routing table information for VRF default
Router identifier 10.11.0.1, ...
Audio Video Bridging
(AVB)
Arista switches support Audio Video Bridging (AVB) and the associated protocols. This section
describes AVB concepts and the implementation of associated protocols.
Topics ...
EVPN Layer 3 Core Operations
The EVPN standard defines a number of operations and functionality to allow the dynamic learning of MAC and IP bindings, management of MAC moves (VM/host mobility), ARP ...
... with route map filtering.
Opaque LSAs (RFC 2370).
Graceful restart (RFC 3623).
OSPF Routes over GRE Tunnels.
Unsupported Features
eos does not support the following OSPFv2 functions in the ...
Segment Security
Overview of MSS-Group
Configuring MSS-Group
Segment Security Considerations
Show Commands
Segment Security
Commands
Overview of MSS-Group
The system supports grouping ...
... its performance or feature set. Filtering syntax is the industry standard.
Note: eos supports egress IPv4 and IPv6 Port Access Control Lists (PACLs) by default. To enable egress MAC PACLs, add the ...
... but they must not overlap. eos disables
overlapping subnets.
The following command enters DHCP Server subnet mode under the IPv4 address
family.switch# config
switch(config)# dhcp server
switch(config-dhcp-server)# ...