Total 50 results found for the keyword of "eos section 35 5 is is commands"
... eos sends hello messages to all known neighbors every
10 seconds. If the switch does not receive
hello responses from a neighbor for 4*10=40 seconds, the switch considers
communication with the neighbor ...
... example, eos sends hello messages to all known neighbors every
10 seconds. If the switch does not receive
hello responses from a neighbor for 4*10=40 seconds, the switch loses
communication and the neighbor
resets.(config-mpls-rsvp)# ...
EVPN and VCS commands
Global Configuration Mode
router
general
Router BGP Configuration Mode
next-hop
resolution disabled
redistribute
service vxlan
route-target
route-target
export
route-target ...
VXLAN commands
VXLAN Global Configuration
commands
interface vxlan
ip address virtual
vxlan vni notation
dotted
VXLAN Interface Configuration
commands
igmp snooping
vxlan flood vtep ...
Upgrade/Downgrade commands
install
reload fast-boot
reload hitless
install
The install command copies the specified eos image onto the switch if the source is external, configures ...
... delete the GM list. If no list exists, eos considers all potential GM clocks by
default.
To delete a single clock, use the no ptp grandmasters clock-identity accepted address_format.
Command Mode
PTP ...
...
The environment overheat command controls the switch's
response to an overheat condition. By default, the switch shuts down when it senses
an overheat condition.
Note: eos does not support overriding ...
Session Management commands
Global Configuration commands
commit timer
configure replace
configure session
management accounts
management api eos-sdk-rpc
management api external-services ...
... 3 boundary values: 0,
boundary_value, infinity.
At most, 4 bins can be specified using 0, infinity, and 3 boundary values.
If you do not configure a binning profile, eos uses the following default
profile:binning ...
7130 Layer 1 commands
Layer 1 Configuration commands
l1 source
Layer 1 Show commands
show l1 destination
show l1 matrix
show l1 path
show l1 source
show l1 source
capabilities
l1 ...
... the encrypted string. If the
clear-text password is lost, delete the corresponding
PASSWORD command line from the
boot-config file.
Note: The eos boot secret command adds or modifies
the PASSWORD configuration ...
... not know the current settings, restore the factory default
settings described in Restoring the Factory Default eos Image and Startup Configuration.
The no boot console and default boot
console commands ...
... the interval between
probes on a client. By default, eos sets the interval to 10 seconds.
Command Mode
Connectivity Monitor Client Configuration Mode
Command Syntax
client interval interval
Parameters ...
... can be enabled or disabled on the
fly without impacting regular packet forwarding functionality.
NDR Switch Sensor Extension
NDR switch sensor extends eos telemetry for network threat detection. The ...
... Ratio, Residual Inter Symbol Interference, PAM4 Level
Transition Parameters, and other parameters supported on optics interfaces.
Using the Performance Monitoring feature allows eos to collect and maintain ...
... This means the directly connected
TaskTracker nodes can belong to different clusters. eos supports a maximum of five
clusters per switch.
MapReduce Tracer Configuration
The MapReduce Tracer structures ...
VM Tracer
This section describes VM Tracer configuration and usage and contains these sections:
Introducing VM Tracer
VM Tracer Description
VM Tracer Configuration Procedures
VM Tracer ...
... The agent gathers data from the MIB and responds to requests for information. For a list of supported MIBs, refer to the release notes for the specific eos version.
This section discusses enabling the ...
...
sFlow exports packet samples and topology meta data to a centralized collector
application.
sFlow scales and operates on all switch ports simultaneously.
eos implements sFlow on all switches, without ...
... a single agent, but supports additional agents to allow multiple CPUs and increase the total number of packets processed. eos
supports up to 8 SFTAgents.
Use the following command to add 3 instances ...