Total 45 results found for the keyword of "eos section 7 2 configuration files"
configuration files
Three files define the switch boot behaviour and configuration state:
boot-config - specifies the location and name of the eos image to be
loaded at boot time.
startup-config - ...
Layer 1 configuration
Enable and configure Layer 1 capabilities on the appropriate hardware platforms.
Layer 1 Profiles
Layer 1 Profiles
Supported Platforms
Platform Support for Module Profiles ...
... to
4 different peers. This creates a split configuration called a breakout.
By default, eos exposes a number of interfaces on a port depending on the number of
configurable signaling lanes. An OSPF transceiver ...
Platform Support for Module Profiles
Use the following support matrix for compatible Module Profiles and Platforms:
Table 1. Built-in Module Profiles
Profile
Compatible Platforms
Uniform-4x100G-2-R ...
... can be enabled or disabled on the
fly without impacting regular packet forwarding functionality.
NDR Switch Sensor Extension
NDR switch sensor extends eos telemetry for network threat detection. The ...
... timestamp
Drop count
Device ID
Egress
interface
FCS type
Reserved
TAP Aggregation Extra MPLS Pop (4 to 6 Labels)
Available starting with eos Release 4.23.1F extra MPLS pop for TAP
Aggregation ...
... clusters. This means the directly connected
TaskTracker nodes can belong to different clusters. eos supports a maximum of five
clusters per switch.
MapReduce Tracer configuration
The MapReduce Tracer ...
... single agent, but supports additional agents to allow multiple CPUs and increase the total number of packets processed. eos
supports up to 8 SFTAgents.
Use the following command to add 3 instances of ...
Latency Analyzer (LANZ)
Arista Networks’ Latency Analyzer (LANZ) is a family of eos features that provide enhanced visibility into network dynamics, particularly in areas related to the delay packets ...
Configuring RSVP-TE Tunnels
Enable the dedicated RSVP-TE Tunnel configuration mode by entering the router
traffic-engineering command to enter the router traffic-engineering mode
and then the rsvp ...
... a GRE tunnel, the payload of the outgoing GRE packet contains the payload of
the incoming source packet starting from the MPLS header. eos
strips L2 and outer L3 headers from the mirror copy. When the
MPLS ...
... Features - When running ASU, eos does not support the following features:
Multi-Chassis Link Aggregation (MLAG)
EVPN Multicast
PIM Bidirectional (PIM-BiDir)
Peer Switch Release Requirement - The ...
... distributes operational state information across a set of eos switches to support applications that provide network services. See the CloudVision User Guide for additional information.
Topics in this ...
... OSPFv2 adjacencies with DR Other neighbors.
OSPFv2 Multiple Instances Support
eos supports multiple OSPFv2 instance configurations on the default VRF and provides isolation as well as segregation ...
... this Locator along with the SIDs. SRv6 computes the reachability to SIDs
using the Locator advertisement. eos supports default-algorithms and FlexAlgo
SIDs.
Multiple node SIDs can be advertised from ...
... list, or profile, of resolution RIB domains (for example, either tunnel or IP domain). This allows eos to direct specific services over the specified RIB domains, overriding the default behavior. Further, ...
...
Maintenance Mode configuration
Maintenance Mode Commands
Overview
Using maintenance mode, you can perform several maintenance activities, such as:
eos image upgrade.
Initial configuration ...
... its performance or feature set. Filtering syntax is the industry standard.
Note: eos supports egress IPv4 and IPv6 Port Access Control Lists (PACLs) by default. To enable egress MAC PACLs, add the ...
... the DHCP Server global mode configurations. There can be
multiple subnets configured, but they must not overlap. eos disables
overlapping subnets.
The following command enters DHCP Server subnet mode ...
... IP address on the interface. When the switch detects the duplicate IP address, eos generates a syslog message. It helps the network operator to identify IP addresses misconfiguration. By default, this ...