Total 50 results found for the keyword of "eos l1 source"
Multicast source Discovery Protocol (MSDP)
Multicast source Discovery
Protocol (MSDP) describes a topology that connects multiple IPv4 Protocol
Independent Multicast Sparse-Mode (PIM-SM) domains. ...
Configuring the source IP
To set the source IP address for all PTP packets, use the ptp source command.
Example
This command configures the source IP address of 10.0.2.1 for all PTP
packets.switch(config)# ...
...
sFlow exports packet samples and topology meta data to a centralized collector
application.
sFlow scales and operates on all switch ports simultaneously.
eos implements sFlow on all switches, without ...
... manager can request or change. The agent gathers data from the MIB and responds to requests for information. For a list of supported MIBs, refer to the release notes for the specific eos version.
This ...
VM Tracer
This chapter describes VM Tracer configuration and usage and contains these sections:
Introducing VM Tracer
VM Tracer Description
VM Tracer Configuration Procedures
VM Tracer Commands ...
... clusters. This means the directly connected
TaskTracker nodes can belong to different clusters. eos supports a maximum of five
clusters per switch.
MapReduce Tracer Configuration
The MapReduce Tracer ...
... can be enabled or disabled on the
fly without impacting regular packet forwarding functionality.
NDR Switch Sensor Extension
NDR switch sensor extends eos telemetry for network threat detection. The ...
... to the same ES where they originated. To overcome this, eos includes ESI
labels to Non-DF PEs as well. This shared ESI label provides a mechanism to achieve sending an
ESI label to Non-DF PEs on platforms ...
RSVP-TE LSR
RSVP-TE applies the Resource Reservation Protocol (RSVP) for Traffic Engineering (TE) to distribute MPLS labels for steering traffic and reserving bandwidth.
The eos implementation supports ...
RSVP-TE LER
RSVP-TE, the Resource Reservation Protocol (RSVP) for Traffic Engineering (TE),
distributes MPLS labels for steering traffic and reserving bandwidth. The Label Edge
Router (LER) feature ...
LDP Pseudowire
LDP pseudowire provides support for emulating Ethernet connections over a
Multiprotocol Label Switching (MPLS) network, and controlled using the extension of the MPLS
Label Distribution ...
...
Examples
In this example, eos sends hello messages to all known neighbors every
10 seconds. If the switch does not receive
hello responsesfrom a neighbor for 4*10=40 seconds, the switch loses
communication ...
... timestamp
Drop count
Device ID
Egress
interface
FCS type
Reserved
TAP Aggregation Extra MPLS Pop (4 to 6 Labels)
Available starting with eos Release 4.23.1F extra MPLS pop for TAP
Aggregation ...
Latency Analyzer (LANZ)
Arista Networks’ Latency Analyzer (LANZ) is a family of eos features that provide enhanced
visibility into network dynamics, particularly in areas related to the delay packets
experience ...
... template interval 3400000
Hardware Flow Tracking with IPFIX Export
Hardware Flow Tracking uses match criteria to collect data from packets based on defined
flow profiles. eos sends the collected ...
Inter-VRF Local Route Leaking
Inter-VRF local route leaking allows the leaking of routes from one VRF (the source VRF) to
another VRF (the destination VRF) on the same router.
Inter-VRF routes can ...
EVPN Multicast VRF Leaking
Overview
EVPN Multicast virtual routing and forwarding (VRF) Leaking forwards multicast
traffic from a sender in a tenant or external domain (VRF) to a different domain
(VRF) ...
... mechanisms in eos and the broader use-cases they support are documented here:
Inter-VRF Local Route Leaking using BGP VPN
Inter-VRF Local Route Leaking using VRF-leak Agent
Configuration
The ...
VCS to EVPN Hitless Migration
VCS to EVPN Hitless Migration enables support for migrating from only using VCS as
the control plane to only using EVPN as a control plane in a hitless manner concerning ...
...
eos adds a new parameter in the output, evpn prefix detail to display the
ATTR_SET, code 128 attributes.
switch#show bgp evpn
BGP routing table information for VRF default
Router identifier 10.11.0.1, ...