Total 50 results found for the keyword of "eos section 18 4 configuring ports"
VXLAN Description
These sections describe VXLAN architecture, the data objects that comprise a VXLAN network, and
process of bridging packets through a VXLAN network.
VXLAN Architecture
VXLAN Gateway ...
Routing Information Protocol (RIP)
This chapter contains the following sections.
RIP Conceptual
Overview
Running RIP
on the Switch
configuring RIP on Multiple VRFs
RIP Commands
RIP Conceptual ...
... for OSPFv2 adjacencies with DR Other neighbors.
OSPFv2 Multiple Instances Support
eos Release 4.22.1F adds support for multiple OSPFv2 instances to
be configured in the default VRF. OSPFv2 Multiple ...
... area and interface levels.
Note: On the same area or interface, eos allows security configuration with either AH or ESP but not both. We can have one area or interface configured with AH and another ...
...
Note: Unlike node segments, anycast segments do not have the ‘N’ flag set described in section 2.1.1.2 of RFC8667.
The following enhancements are available by release:
eos Release 4.22.1F adds support ...
... hop resolution semantics of BGP routes with an ordered list, or profile, of resolution RIB domains (for example, either tunnel or IP domain). This allows eos to direct specific services over the specified ...
...
Maintenance Mode Configuration
Maintenance Mode Commands
Overview
Using maintenance mode, you can perform several maintenance activities such as:
eos image upgrade.
Initial configuration or ...
... and destination
addresses..
ACLs can also be made dynamic (not persisting in the eos), and the
payload keyword can be used to
turn an ACL into a User-Defined Field (UDF) alias for use in other ACLs. ...
VRRP and VARP
A virtual IP (VIP) address
is an IP address that does not directly connect to a specific interface.
Inbound packets sent to a Virtual IP address are redirected to a physical
network ...
... that are configured by a custom agent using the eos SDK or eAPI
and age out (expire) after a specified time period.
For example, if you are using a custom agent that reacts to traffic sent to the CPU ...
Nexthop Groups
These sections describe the Nexthop groups:
Nexthop Group Description
Nexthop Group Configuration
Support for IPv6 Link-Local Addresses in Nexthop Groups Entries
Nexthop Group Commands ...
... distributes operational state information across a set of eos switches to support applications that provide network services. See the CloudVision User Guide, https://www.arista.com/en/support/product-documentation, ...
...
configuring Priority-Flow-Control (PFC)
configuring PFC Watchdog
DCBX and Flow Control Commands
Introduction
eos implements Link Layer Discovery
Protocol (LLDP) and the Data Center Bridging ...
Layer 2 Protocol Forwarding
Layer2 (L2) Protocol Forwarding on Ethernet interfaces is supported, in addition to
Type-5 PW. Also, selective forwarding of certain L2 Protocol packets
(tagged/untagged/all) ...
... VOQ0 are in WRR with a static credit ratio 2:3:6 (higher ratio
implies more credits).
The subinterface inherits the trust mode of the parent interface.
Before eos Release 4.24.2F, shaping is supported ...
... ensure disable-vrf configuration to take effect.
switch(config)# agent SandL3Unicast terminate
SandL3Unicast was terminated
Starting from the eos Release 4.26.0F, /32 prefix length optimization ...
... snooping is a Layer 2 feature that is
configured on LAN switches. The Arista eos switch supports Option-37 insertion that
allows relay agents to provide remote-id information in DHCP request packets. DHCP
servers ...
... The maximum number of ports per LAG varies by platform; numbers for each
platform in the latest eos release are available here: https://www.arista.com/en/support/product-documentation/supported-features. ...
... MLAG peer switches are identical platforms and run identical eos images. Running different images/platform may result in a failure to form an association with the MLAG peer or see discrepancy in behavior. ...
... Type ports
---- ----------- ---- -----
Total Mac Addresses for this criterion: 0
Beginning with eos Release 4.26.0F,
portsec-Protect enforces a limit on the number of MAC
addresses, ...