Total 37 results found for the keyword of "eos section 2 3 configure session"
configure session
The command configure session allows users to issue
configuration sessions as CLI commands that do not take effect immediately. Each
configure session is saved with a unique name. ...
... server. Command authorization can be provided by eos local configuration
or TACACS+. The XMPP server should use the same authentication source
as the switches. RADIUS is not supported as an XMPP authorization ...
sFlow
This chapter describes Arista's implementation of sFlow, including configuration instructions and command descriptions. Topics covered by this chapter include:
sFlow Conceptual Overview
sFlow ...
VM Tracer
This chapter describes VM Tracer
configuration and usage and contains these sections:
VM Tracer Introduction
VM Tracer Description
VM Tracer Configuration Procedures
VM Tracer ...
Sample Configurations
EVPN VXLAN IRB Sample Configuration
In the topology below, we are connecting a Layer 2 site with a Layer 3 site using Layer 3
EVPN (type-5 route). Right side leaves are MLAG ...
Multiprotocol Label Switching (MPLS)
Tunneling protocols encapsulate packets of a different protocol as the payload of a larger frame for delivery within networks utilizing the encapsulating protocol. ...
Multiprotocol Label Switching (MPLS)
Tunneling protocols encapsulate packets of a different protocol as the payload of a larger frame for delivery within networks utilizing the encapsulating protocol. ...
Multiprotocol Label Switching (MPLS)
Tunneling protocols encapsulate packets of a different protocol as the payload of a larger frame for delivery within networks utilizing the encapsulating protocol. ...
Multiprotocol Label Switching (MPLS)
Tunneling protocols encapsulate packets of a different protocol as the payload of a larger frame for delivery within networks utilizing the encapsulating protocol. ...
...
TAP Aggregation QoS Handling on TAP Ports
Before eos 4.20.5F, QoS behavior was not enforced for TAP aggregation ports, meaning that QoS
behavior for packets passing through the device was not ...
Multicast Source Discovery Protocol (MSDP)
Multicast Source Discovery
Protocol (MSDP) describes a topology that connects multiple IPv4 Protocol
Independent Multicast Sparse-Mode (PIM-SM) domains. ...
... it is binding a label.
Note: All connected interfaces are advertised as bound. However, eos currently advertised labels for /32 addresses, and FEC filter is configured to install only x.x.x.200/32 prefixes. ...
... of routes will result in data loss.
This can be prevented by configuring graceful restart on the device.
When IS-IS is used as the interior gateway
protocol (IGP), the following eos features require nonstop ...
...
Configuring BGP in a VRF
IPv6 VRF support in eos allows application of a BGP configuration to a single VRF instance, overriding global commands. To apply VRF-specific BGP configuration, use the ...
... Features
Maintenance Mode Configuration
Maintenance Mode Commands
Overview
Using maintenance mode, you
can perform several maintenance activities such as:
eos image upgrade
Initial configuration
or ...
... packets.
The basic behavior of BFD is defined in
RFC 5880.
BFD Modes
BFD functions in asynchronous or demand mode, and also offers an echo function. eos supports
asynchronous mode and the echo ...
Multicast Architecture
IP multicast is the transmission of data packets to multiple hosts through a common IP address. Arista switches support multicast transmissions through IGMP, IGMP Snooping, ...
VARP
Virtual-ARP (VARP) allows multiple
switches to simultaneously route packets from a common IP address in
an active-active router configuration. Each switch is configured with
the same set of virtual ...
... This feature is designed to be used for
flows that are configured by a custom agent using the eos SDK or eAPI
and age out (expire) after a specified time period.
For example, if you are using a custom
agent ...
... allows for configuring IPv4, IPv6, and MAC access lists and then updating a monitor session with corresponding configuration changes. eos mirrors the packets that match permit statements. eos does not ...