Total 43 results found for the keyword of "eos section 25 4 route management"
...
Note: Unlike node segments, anycast segments do not have the ‘N’ flag set described in section 2.1.1.2 of RFC8667.
The following enhancements are available by release:
eos Release 4.22.1F adds support ...
... hop resolution semantics of BGP routes with an ordered list, or profile, of resolution RIB domains (for example, either tunnel or IP domain). This allows eos to direct specific services over the specified ...
VRRP and VARP
A virtual IP (VIP) address
is an IP address that does not directly connect to a specific interface.
Inbound packets sent to a Virtual IP address are redirected to a physical
network ...
... that are configured by a custom agent using the eos SDK or eAPI
and age out (expire) after a specified time period.
For example, if you are using a custom agent that reacts to traffic sent to the CPU ...
Nexthop Groups
These sections describe the Nexthop groups:
Nexthop Group Description
Nexthop Group Configuration
Support for IPv6 Link-Local Addresses in Nexthop Groups Entries
Nexthop Group Commands ...
...
Configuring Priority-Flow-Control (PFC)
Configuring PFC Watchdog
DCBX and Flow Control Commands
Introduction
eos implements Link Layer Discovery
Protocol (LLDP) and the Data Center Bridging ...
... Locking Commands
IP Locking
IP Locking is an eos feature configured on an Ethernet Layer 2 port.
When enabled, IP Locking ensures that a port will only permit IP and ARP packets with IP
source ...
... ensure disable-vrf configuration to take effect.
switch(config)# agent SandL3Unicast terminate
SandL3Unicast was terminated
Starting from the eos Release 4.26.0F, /32 prefix length optimization ...
... snooping is a Layer 2 feature that is
configured on LAN switches. The Arista eos switch supports Option-37 insertion that
allows relay agents to provide remote-id information in DHCP request packets. DHCP
servers ...
... (eos release
4.25.2F)
Support of 400GBASE-ZR with Open Forward Error Correction (O-FEC) (eos release
4.25.2F)
Override a transceiver slot’s maximum power limit (eos release
4.25.2F)
Platform Compatibility ...
... MLAG peer switches are identical platforms and run identical eos images. Running different images/platform may result in a failure to form an association with the MLAG peer or see discrepancy in behavior. ...
... Type Ports
---- ----------- ---- -----
Total Mac Addresses for this criterion: 0
Beginning with eos Release 4.26.0F,
PortSec-Protect enforces a limit on the number of MAC
addresses, ...
... - Chassis ID type: MAC address (4)
Chassis ID : 001c.730f.11a8
- System Name: "switch.aristanetworks.com"
- System Description: "Arista Networks eos version 4.13.2F running on an Arista
Networks ...
... Configuration
Procedures
VLAN Configuration
Commands
VLAN Introduction
Arista switches support industry standard 802.1q VLANs. Arista eos provides tools to manage and extend VLANs throughout the ...
...
The switch controls access to eos commands by authenticating user identity and verifying user authorization. Authentication, Authorization, and Accounting (AAA) activities are conducted through three ...
...
MACsec Licensing
MACsec encryption is a eos licensed feature. A valid MACsec license must be configured on a switch. MACsec licenses are tied to a switch serial number and the licensee. ...
...
eos is optimized to support QoS configuration on the Fabric interfaces on 7250x and 7300 series switches. Configuring QoS on the Fabric interfaces in addition to front panel ports allows user to have ...
... the eos image with Smart System
Upgrade
Using SSU to upgrade the active eos image is a five-step process:
Prepare switch for upgrade ( Prepare the Switch for SSU).
Transfer image file to the switch ...
Standard Upgrades and Downgrades
Standard software upgrades
and downgrades on Arista switches are accomplished by installing a different
eos image and reloading the switch. On switches with redundant ...
... command replaces the EOS CLI prompt with an SQLite
prompt.switch# event-monitor interact
sqlite>
This command exits SQLite and returns to the EOS CLI
prompt.sqlite> .quit
switch#
event-monitor ...