Total 50 results found for the keyword of "eos section 28 11 ipv4 commands"
...
show traffic-engineering database
Use the show traffic-engineering database to display the topology used for CSPF computations. Starting from eos Release 4.23.1F, the SRLG group details of a neighbor ...
EVPN and VCS commands
Global Configuration Mode
router
general
Router BGP Configuration Mode
next-hop
resolution disabled
redistribute
service vxlan
route-target
route-target
export
route-target ...
VXLAN commands
VXLAN Global Configuration
commands
interface vxlan
ip address virtual
vxlan vni notation
dotted
VXLAN Interface Configuration
commands
vxlan flood vtep
vxlan multicast-group ...
... ensure disable-vrf configuration to take effect.
switch(config)# agent SandL3Unicast terminate
SandL3Unicast was terminated
Starting from the eos Release 4.26.0F, /32 prefix length optimization ...
Ingress and Egress Per-Port for ipv4 and IPv6 Counters
This feature provides support for per-interface ingress and egress packet and byte counters for both ipv4 and IPv6.
This section describes Ingress ...
Precision Time Protocol (PTP) commands
PTP commands
ptp announce interval
ptp announce timeout
ptp delay-mechanism
ptp delay-req interval
ptp domain
ptp enable
ptp forward-v1
ptp hold-ptp-time ...
... command replaces the EOS CLI prompt with an SQLite
prompt.switch# event-monitor interact
sqlite>
This command exits SQLite and returns to the EOS CLI
prompt.sqlite> .quit
switch#
event-monitor ...
... displays
information about the active flows maintained in the eos.
Command Mode
EXEC
Command Syntax
show flow tracking sampled flow-table [
detail | dst-ip |
dst-port | group |
interface | protocol ...
... rates also decrease the amount of processing
time available for other eos applications.
With hardware acceleration, all sFlow processing is done in hardware
using specialized chips, called accelerators. ...
... can request or change. The agent gathers data from the MIB and responds to requests for information. For a list of supported MIBs, refer to the release notes for the specific eos version.
This chapter ...
... leaks in eos or customer user processes.
Process leaks to too many processes or scripts running at one time.
Over configuration of the system requiring more memory than available.
Large number of temporary ...
... be enabled or disabled on the fly
without impacting regular packet forwarding functionality.
AVA Switch Sensor Extension
AVA switch sensor extends eos telemetry for network threat detection. The FlowWatcher
agent ...
RSVP-TE LSR
RSVP-TE applies the Resource Reservation Protocol (RSVP) for Traffic Engineering (TE), that is, to distribute MPLS labels for steering traffic and reserving bandwidth.
The eos implementation ...
...
Drop count
Device ID
Egress interface
FCS type
Reserved
TAP Aggregation Extra MPLS Pop (4 to 6 Labels)
Available starting with eos Release 4.23.1F extra MPLS pop for TAP Aggregation ...
Latency Analyzer (LANZ)
Arista Networks’ Latency
Analyzer (LANZ) is a family of eos features that provide enhanced visibility
into network dynamics, particularly in areas related to the delay packets
experience ...
EVPN VXLAN Single-Gateway Centralized Routing
In a traditional EVPN VXLAN centralized anycast gateway deployment, multiple L3 VTEPs
serve the role of the centralized anycast gateway. In order for ...
Inter-VRF Local Route Leaking
Inter-VRF local route leaking
allows the leaking of routes from one VRF (the source VRF) to another
VRF (the destination VRF) on the same router. Inter-VRF routes can ...
VCS to EVPN Hitless Migration
VCS to EVPN Hitless Migration enables support for migrating from only using VCS as the control plane to only using EVPN as a control plane in a hitless manner with respect ...
Sample Configurations
EVPN VXLAN IRB Sample Configuration
In the topology below, we are connecting a Layer 2 site with a Layer 3 site using Layer 3
EVPN (type-5 route). Right side leaves are MLAG ...
...
Starting in Release eos 4.23.1, ingress on inner IP header matching
in MPLS packets is also supported on PBR ACLs. In order to enable this, the following must
be configured in a user-defined TCAM profile: ...