Product Compliance

Figure 1. Singapore IMDA Registration Mark

Quick Start Guide
Edge Threat Management
Appliance
CCA-ETM-Q6E
Arista Networks

www.arista.com

DOC-06004-02

Headquarters
5453 Great America Parkway
Santa Clara, CA 95054, USA
+1-408 547-5500
www.arista.com
Support
+1-408 547-5502
+1-866 476-0000
This email address is being protected from spambots. You need JavaScript enabled to view it.
Sales
+1-408 547-5501
+1-866 497-0000
This email address is being protected from spambots. You need JavaScript enabled to view it.
© Copyright 2023 Arista Networks, Inc. The information contained herein is subject to change without notice. Arista Networks and the Arista logo are trademarks of Arista Networks, Inc., in the United States and other countries. Other product or service names may be trademarks or service marks of others.

Overview

This guide is intended for properly trained service personnel and technicians who need to install selected Arista Networks appliances.

The following topics are covered in this section:

Scope

This guide is intended for properly trained service personnel and technicians who need to install the following Arista appliance:

CCA-ETM-Q6E

Important:

Only qualified personnel should install, service, or replace this equipment.

Seul le personnel qualifié doit installer, service, ou remplacer cet équipement.

Receiving and Inspecting the Equipment

Upon receiving the appliance, inspect the shipping boxes and record any external damage. Retain packing materials if you suspect that part of the shipment is damaged; the carrier may need to inspect them.

If the boxes were not damaged in transit, unpack them carefully. Ensure that you do not discard any accessories that may be packaged in the same box as the main unit.

Inspect the packing list and confirm that you received all listed items. Compare the packing list with your purchase order. Parts List provides a list of components included with the appliance.

Installation Process

The following tasks are required to install and use the appliance:
  1. Select and prepare the installation site (Site Selection).
  2. Assemble the installation tools listed (Tools and Parts Required for Installation).
  3. Install the appliance (Mounting the Appliance).
  4. Connect the appliance to the power source and network appliances (Cabling the Appliance).
  5. Configure the appliance (Configuring the Appliance).
    Important:

    Class 1 Laser Product: This product has provisions to install Class 1 laser transceivers which provide optical coupling to the communication network. Once a Class 1 laser product is installed, the equipment is a Class 1 Laser Product. The customer is responsible for selecting and installing the Class 1 laser transceiver and for insuring that the Class 1 AEL (Allowable Emission Limit) per EN/IEC 60825, CSA E60825-1, and Code of Federal Regulations 21 CFR 1040 is not exceeded after the laser transceiver have been installed. Do not install laser products whose class rating is greater than 1. Refer to all safety instructions that accompanied the transceiver prior to installation. Only Class 1 laser appliances, certified for use in the country of installation by the cognizant agency are to be utilized in this product.

     

    Produit Laser de classe 1: Ce produit a des dispositions pour installer des émetteurs-récepteurs de laser de classe 1 qui offre de couplage au réseau de communication optique.Une fois un produit laser de classe 1 est installé, l'équipement est un produit Laser de classe 1 (Appareil à Laser de Classe 1).Le client est responsable pour sélectionner et installer l'émetteur/récepteur de laser de classe 1 et pour assurer que la classe 1 AEL (limite d'émission admissible) par EN/IEC 6-825, CSA E60825-1, et Code des règlements fédéraux 21 CFR 1040 ne soit pas dépassée après avoir installé l'émetteur/récepteur de laser. Ne pas installer des appareils à laser dont la cote de classe est supérieure à 1.Voir toutes les consignes de sécurité qui ont accompagné l'émetteur-récepteur avant l'installation. Seuls appareils laser de classe 1 certifiés pour une utilisation dans le pays d’installation par l’organisme compétent doivent être utilisées dans ce produit.

     

    Important:

    Ultimate disposal of this product should be handled in accordance with all national laws and regulations.

    Aucune pièce réparable par l'utilisateur à l'intérieur. Confiez toute réparation à un technicien qualifié.

Obtaining Technical Assistance

Any customer, partner, reseller, or distributor holding a valid Arista Service Contract can obtain technical support in any of the following ways:

Specifications

Table 1. Appliance Specifications (Dimensions and Weights)
Appliance Size (W x D x H) Weight
CCA-ETM-Q6E 232mm x 174mm x 42mm 1.4 kg

 

 

Table 2. Appliance Specification (Operational and Storage)
Appliance Operating Temperature and Humidity Storage Temperature and Humidity Operating Altitude
CCA-ETM-Q6E 0°C to 40°C

10 to 90% RH

 -20°C to 70°C

5 to 95% RH

 Sea level to 5000 meters.

 

 

Table 3. Appliance Specifications (Power Input)
Power Source Ratings
AC INPUT - 40W Power Adapter 100~240V, 1.2A, 50-60Hz

 

Preparation

The following topics are covered in this section:

Site Selection

The following criteria should be considered when selecting a site to install the appliance.

  • Temperature and Ventilation: For proper ventilation, install the appliance where there is ample airflow to the front and back of the appliance. The ambient temperature should not go below 0° or exceed 40°C.
    Important: To prevent the appliance from overheating, do not operate it in an area where the ambient temperature exceeds 40°C (104°F).

    Pour empêcher l’interrupteur de surchauffe, ne pas utiliser il dans une zone où la température ambiante est supérieure à 40°C (104°F).

  • Rack Space: Install the appliance in a 19" rack or cabinet. The appliance height is 1 RU. The rack mounting kit provides mounting brackets for two-post racks.

When mounting the appliance in a partially filled rack, load the rack from bottom to top, with the heaviest equipment at the bottom. Load the appliance at the bottom if it is the only item in the rack.

  • Other Requirements: Select a site where liquids or objects cannot fall onto the equipment and foreign objects are not drawn into the ventilation holes. Verify these guidelines are met:
    • Clearance areas to the front and rear panels allow for unrestricted cabling.
    • All front and rear panel indicators can be easily read.
    • Power cords can reach from the power outlet to the connector on the rear panel.
      Important: All power connections must be removed to de-energize the unit.

      Toutes les connexions d’alimentation doivent être enlevées pour hors tension l’appareil.

Tools and Parts Required for Installation

The following tool(s) are required for installation:

  • Philips #1 screwdriver

Electrostatic Discharge Precautions

Observe these guidelines to avoid ESD damage when installing or servicing the appliance:
  • Assemble or disassemble equipment only in a static-free work area.
  • Use a conductive work surface (such as an anti-static mat) to dissipate static charge.
  • Wear a conductive wrist strap to dissipate static charge accumulation.
  • Minimize handling of assemblies and components.
  • Keep replacement parts in their original static-free packaging.
  • Remove all plastic, foam, vinyl, paper, and other static-generating materials from the work area.
  • Use tools that do not create ESD.

Cabling the Appliance

For all installations:

  1. Plug in the power adapter to a power source and connect it to the DC 12V power input on the rear panel.
  2. Connect an Ethernet cable from your Internet modem or router to WAN Port 1.
  3. Connect an Ethernet cable from your local network to LAN Port 1.
  4. Power on the system by pressing the power button located on the rear panel next to the power input.
  5. Allow approximately two minutes for the system to initialize before continuing with the next steps

Configuring the Appliance

Getting Started

You can manage your appliance via Edge Threat Management Dashboard or from the local network.

From Edge Threat Management Dashboard

  1. Navigate your web browser to https://edge.arista.com/cmd.

  2. Log in with your Edge Threat Management Dashboard account, or click Create Account to set up an account.

  3. Navigate to the Appliances screen and click Add.

  4. Enter the serial number located on the bottom of your appliance.

  5. Click Add to confirm the new appliance.
  6. Complete the initial setup to begin managing your appliance.
From the local network

  1. Connect an Ethernet cable from your management computer or LAN appliance to the LAN port.

  2. From your management computer, check the network status of your system and confirm that you receive an IPv4 address in the subnet of 192.168.1.0/24 (e.g. 192.168.1.100).

  3. In a browser, navigate to http://192.168.1.1.

  4. Follow the steps in your browser to complete the setup.

Status Indicators

The following topics are covered in this section:

Front Indicators



1 Speed status 4 WAN/SFP connections
2 Data 5 LAN Gb Ethernet connections
3 Power 6 Connection status

Parts List

Package Contents

The CCA-ETM-Q6E package includes:



1 Power adapter 4 Rubber Feet
2 Power cable 5 Mounting Screws
3 VESA wall mount bracket 6 VESA bracket screws

Rear Panel

This appendix displays the rear panel of all appliances covered by this guide.

1 LAN Gb Ethernet ports 5 Console port
2 SFP WAN ports 6 Power button
3 Ethernet WAN ports 7 Power supply port
4 3.0 USB ports    
Note: The SFP WAN ports and Ethernet WAN ports are "combo ports". A choice must be made between SFP and Ethernet ports for the designated port number.

Regulatory Model Numbers

This appendix covers the Regulatory Model Number for the appliance in this guide.

Table 1. Regulatory Model Numbers and Product Numbers
Regulatory Model Numbers (RMN) Product Numbers
AN2207, CAF-0262-5621-E90 CCA-ETM-Q6E