Total 41 results found for the keyword of "eos section 29 2 configuring bgp"
configuring RSVP-TE
The configuration of RSVP-TE requires the configuration of one or more of the following:
configuring RSVP-TE LER
configuring RSVP-TELSR
configuring RSVP-TE P2MP LER ...
... require the customer routes have them.
eos achieves the above through the extensions to bgp as defined in RFC 4364 for IPv4
and RFC 4659 for IPv6, and the use of VPN Routing and Forwarding Tables (VRFs),
Route ...
...
eos adds a new parameter in the output, evpn prefix detail to display the
ATTR_SET, code 128 attributes.
switch#show bgp evpn
bgp routing table information for VRF default
Router identifier 10.11.0.1, ...
... router-mac ba:ed:43:3f:ca:8e
MLAG
This feature applies only to the scenario when two different MLAG VTEP pairs learn the
remote prefix.
Prior to 4.26.0F, eos supports this feature on the primary ...
... list, or profile, of resolution RIB domains (for example, either tunnel or IP domain). This allows eos to direct specific services over the specified RIB domains, overriding the default behavior. Further, ...
...
sFlow exports packet samples and topology meta data to a centralized collector
application.
sFlow scales and operates on all switch ports simultaneously.
eos implements sFlow on all switches, without ...
... template interval 3400000
Hardware Flow Tracking with IPFIX Export
Hardware Flow Tracking uses match criteria to collect data from packets based on defined
flow profiles. eos sends the collected ...
... timestamp
Drop count
Device ID
Egress
interface
FCS type
Reserved
TAP Aggregation Extra MPLS Pop (4 to 6 Labels)
Available starting with eos Release 4.23.1F extra MPLS pop for TAP
Aggregation ...
... this example, eos sends hello messages to all known neighbors every
10 seconds. If the switch does not receive
hello responsesfrom a neighbor for 4*10=40 seconds, the switch loses
communication and the ...
... a GRE tunnel, the payload of the outgoing GRE packet contains the payload of
the incoming source packet starting from the MPLS header. eos
strips L2 and outer L3 headers from the mirror copy. When the
MPLS ...
... eos Release 4.22.0F, the EVPN VXLAN L3 Gateway using EVPN IRB
supports routing traffic from one IPv6 host to another IPv6 host on a stretched VXLAN
VLAN.
IP VPNs Sample Configuration
Here, we examine ...
VCS to EVPN Hitless Migration
VCS to EVPN Hitless Migration enables support for migrating from only using VCS as
the control plane to only using EVPN as a control plane in a hitless manner concerning ...
Inter-VRF Local Route Leaking
Inter-VRF local route leaking allows the leaking of routes from one VRF (the source VRF) to
another VRF (the destination VRF) on the same router.
Inter-VRF routes can ...
...
VXLAN Decapsulation for interface with multiple VRFs
Please refer to the following security advisory after the eos software upgrade for a
network that leverages VXLAN decapsulation on an interface ...
Ethernet VPN (EVPN)
This chapter describes the Arista EVPN implementation. sections in this chapter
include the following topics:
EVPN Overview
EVPN Layer
3 Core Operations
Integrated Routing and ...
... the advertising router ID, along with the extended
communities of tunnel type (MPLS), MPLS Label value and
route-target.
Note: You require Release eos 4.21.1F and later versions with Jericho/Jericho+
platforms. ...
... of the LDP
neighbor for which it is binding a label. Note: All connected interfaces are
advertised as bound. However, eos currently advertised labels for /32 addresses, and
FEC filter is configured ...
Multicast Source Discovery Protocol (MSDP)
Multicast Source Discovery Protocol (MSDP) describes a topology that connects multiple IPv4 Protocol Independent Multicast Sparse-Mode (PIM-SM) domains. ...
... interface vlan 8
switch(config-if-Vl8)# pim ipv4 sparse-mode
switch(config-if-Vl8)#
Enabling PIM IPv6 Sparse Mode
By default, eos disables IPv6 PIM disabled on an interface. The pim ipv6 sparse-mode ...
... Beginning with eos Release 4.25.0F, MLDv2 snooping is supported on MLAG deployments.
Limitations
The extraneous “Switch” interface should be ignored in show mld
snooping counters and show mld snooping
counters ...