- Written by Prashanth Rajendran
- Posted on 11月 14, 2019
- Updated on 11月 15, 2019
- 7566 Views
This feature adds support for BGP peering over IPv6 link local addresses. This feature is available with the with the
- Written by Manoj Agiwal
- Posted on 9月 30, 2015
- Updated on 7月 12, 2024
- 16994 Views
BGP Non Stop Forwarding (NSF) aims to minimize the traffic loss when the the following scenarios occur:
- Written by Bhavin Patel
- Posted on 3月 24, 2020
- Updated on 2月 15, 2024
- 9544 Views
This feature allows failover to the backup path to occur in constant time per interface going down for features such as RSVP link protection, RSVP node protection, TI-LFA link protection, and BGP PIC. Without this feature enabled, it would take time proportional to the number of paths going over the interface experiencing the link down event to failover to the backup path. With this feature enabled, the failover time would be constant regardless of the number of paths.
- Written by Huong Nguyen
- Posted on 11月 13, 2019
- Updated on 10月 12, 2023
- 13037 Views
Support for DHCPv4 (RFC 2131) and DHCPv6 Server (RFC 8415) was added to EOS-4.22.1 and EOS-4.23.0 respectively. EOS DHCP server leverages ISC Kea as backend. The router with DHCP Server enabled acts as a server that allocates and delivers network addresses with desired configuration parameters to its hosts.
- Written by Krzysztof Gongolewski
- Posted on 9月 11, 2022
- Updated on 8月 30, 2024
- 6439 Views
Dynamic NAT connection limit is a feature which allows to limit the number of dynamic NAT connections.
- Written by Konrad Ciekot
- Posted on 10月 24, 2019
- Updated on 10月 24, 2019
- 9296 Views
As of 4.22.1F Load Balance Profiles can be used to explicitly configure ECMP Load Balance parameters. In addition,
- Written by Sourabh Bollapragada
- Posted on 12月 22, 2020
- Updated on 1月 29, 2024
- 7919 Views
This feature supports counting ECN-marked packets (ECN = Explicit Congestion Notification) on a per egress port per tx-queue basis. The feature can be used to gather these packet counts via CLI or SNMP. There are two cases when an ECN-marked (congestion) packet is counted on the egress port/queue:
- Written by James Shephard
- Posted on 8月 25, 2019
- Updated on 7月 5, 2023
- 10465 Views
Forwarding destination prediction enables visibility into how a packet is forwarded through the switch, allowing you to determine which interfaces a packet would egress out of. Typical use cases include, but are not limited to, determining egress members for Port-Channels and ECMPs.
- Written by Sarah Chen
- Posted on 10月 9, 2019
- Updated on 10月 9, 2019
- 7180 Views
The General Router ID configuration provides the ability to configure a common Router ID for all routing protocols
- Written by Dawon Lee
- Posted on 8月 17, 2018
- Updated on 7月 5, 2024
- 8129 Views
Lanz Mirroring feature allows users to automatically mirror traffic queued as a result of congestion to either CPU or a different interface.
- Written by Rahul Kumar Singh
- Posted on 11月 7, 2019
- Updated on 12月 27, 2021
- 7425 Views
In campus network deployments, classification of the devices connected to a switch port is required. Based on the
- Written by Michelle Wang
- Posted on 8月 28, 2019
- Updated on 10月 23, 2023
- 6772 Views
SSH certificates (as implemented by OpenSSH, introduced in version 5.4) allow for easy management of user authentication and authorization for passwordless logins, as well as host verification.
- Written by Sandeep Kopuri
- Posted on 10月 7, 2019
- Updated on 5月 17, 2024
- 10486 Views
Topology Independent Fast Reroute, or TI-LFA, uses IS-IS SR to build loop-free alternate paths along the post-convergence path. These loop-free alternates provide fast convergence.
- Written by Shyam Kota
- Posted on 5月 21, 2019
- Updated on 6月 7, 2023
- 8627 Views
Add the ability to generate SYSLOG messages when a transceiver's digital optical monitoring threshold is crossed.