- Written by Ajay Kini
- Posted on 6月 21, 2020
- Updated on 2月 15, 2024
- 8794 Views
Accumulated IGP Metric (AIGP) is an optional non-transitive BGP attribute used to carry an IGP metric with BGP route advertisements. The AIGP attribute is useful for tie-breaking in BGP bestpath selection so that routing decisions can be made on the basis of shortest path/lowest IGP cost path amongst multiple BGP paths. This is particularly applicable in scenarios where a single administration is subdivided into multiple Autonomous Systems (AS) each with similar routing policies and the same IGP in use such that the IGP metric for a route can be propagated usefully between the ASes so as to let receiving BGP speakers make routing decisions based on the cumulative IGP cost of the route. This set of ASes in a common administrative domain in the context of advertising and receiving the AIGP attribute are referred to as an AIGP administrative domain.
- Written by Joshua Boe
- Posted on 6月 29, 2023
- Updated on 6月 30, 2023
- 6269 Views
The cEOS-lab and vEOS-lab platforms use a different “forwarding plane” than EOS and CloudEOS; it is a software forwarding agent called Etba. A more efficient Etba provides more flexibility and better scalability for virtual network simulation for cEOS-lab and vEOS-lab users.
- Written by Jason Shamberger
- Posted on 3月 11, 2020
- Updated on 11月 14, 2024
- 16202 Views
EOS 4.21.3F introduces support for BGP Flowspec, as defined in RFC5575 and RFC7674. The typical use case is to filter or redirect DDoS traffic on edge routers.
- Written by Nandan Saha
- Posted on 8月 24, 2020
- Updated on 5月 22, 2024
- 11488 Views
The BGP-LS extension allows IGPs (OSPF/IS-IS) link state database information to be injected into BGP. This is typically used in deployments where some external component, (like a controller or Path Computation Engine) can do centralized path computations by learning the entire IGP topology through BGP-LS. The controller can then communicate the computed paths based on the BGP-LS updates to the head end device in the network. The mechanism used by the controller to communicate the computed TE paths is outside the scope of this document. Using BGP-LS instead of an IGP peering with the controller to distribute IGP link state information has the following advantages.
- Written by Yini Wang
- Posted on 6月 29, 2023
- Updated on 10月 25, 2023
- 4658 Views
BGP session based dynamic route injection provides the capability to control route injection into IS-IS based on BGP session status since EOS 4.30.1F. When the BGP session is down, the BGP peers addresses will be un-injected from IS-IS.
- Written by Christopher Neilson
- Posted on 6月 29, 2023
- Updated on 7月 3, 2023
- 5558 Views
This feature adds support for gNMI access to the last-configuration-timestamp YANG node in the OpenConfig/Octa agent. When a gNMI set is completed, the last-configuration-timestamp is updated. When the configuration is changed via CLI or some other mechanism, the change eventually propagates to the OpenConfig/Octa agent, which will update the last-configuration-timestamp.
- Written by Ravikumar Chandrasekaran
- Posted on 6月 29, 2023
- Updated on 7月 13, 2023
- 4903 Views
The above figure depicts a typical wireless network deployment. In the above deployment, the traffic from wireless networks are encapsulated into VXLAN tunnels by the AP (Access Point) VTEPs and terminated at the aggregation switches. When a host on the wireless network transmits a DHCP request broadcast packet, the AP encapsulates it in a VXLAN tunnel and sends it to the aggregation switch.
- Written by Huong Nguyen
- Posted on 11月 13, 2019
- Updated on 10月 12, 2023
- 13624 Views
Support for DHCPv4 (RFC 2131) and DHCPv6 Server (RFC 8415) was added to EOS-4.22.1 and EOS-4.23.0 respectively. EOS DHCP server leverages ISC Kea as backend. The router with DHCP Server enabled acts as a server that allocates and delivers network addresses with desired configuration parameters to its hosts.
- Written by Anand Narayanan Rao
- Posted on 6月 20, 2022
- Updated on 7月 3, 2023
- 6700 Views
In vEos/CloudEos deployed as a WAN router, when DPS (Dynamic Path Selection) is configured, all the user traffic coming from the LAN side and going to the WAN side gets load balanced on the DPS paths. This feature enables the automatic discovery of end to end Path MTU for a DPS Path through an internal probing mechanism.
- Written by Johnny Chen
- Posted on 6月 24, 2021
- Updated on 5月 9, 2024
- 11704 Views
ECMP Hash visibility CLI determines the output interface for an ECMP set based on the flow parameters supplied by the user. Ingress interface, source IP address, destination IP address and IP protocol are the required parameters.
- Written by Tanuj Kumar Jhamb
- Posted on 6月 29, 2023
- Updated on 7月 5, 2023
- 4638 Views
sFlow is a sampling technique which monitors incoming traffic on all interfaces without affecting network performance. Egress sFlow is a feature which samples the packets in the egress pipeline for analytical purposes. Currently egress sFlow is only software based on Arista switches.
- Written by Jeevan Kamisetty
- Posted on 8月 23, 2022
- Updated on 11月 30, 2023
- 9768 Views
NDR switch sensor aka “monitor security awake” feature provides deep network analysis by doing deep packet inspection of some or all packets of traffic that's forwarded by the switch.
- Written by Wenteng Ma
- Posted on 6月 29, 2023
- Updated on 7月 3, 2023
- 5018 Views
This feature allows configuring an IPv4 static route with IPv6 nexthop, both the interface and associated IPv6 address as nexthop router; the associated IPv6 address could be a linklocal address.
- Written by Vamsi Anne
- Posted on 10月 20, 2022
- Updated on 11月 19, 2024
- 7727 Views
As Ethernet technologies made their way into the Metropolitan Area Networks (MAN) and the Wide Area Networks (WAN) from the conventional enterprise level usage, they are now widely being used by service providers to provide end-to-end connectivity to customers. Such service provider networks are typically spread across large geographical areas. Additionally, the service providers themselves may be relying on certain internet backbone providers, referred to as “operators”, to provide connectivity in case the geographical area to be covered is too huge.
- Written by Alton Lo
- Posted on 6月 29, 2023
- Updated on 6月 30, 2023
- 6169 Views
EVPN Multihoming defines a mechanism for Multihoming PEs to quickly signal, to remote PEs, a failure in an Ethernet Segment (ES) connectivity with the use of Ethernet A-D per ES route
- Written by James Shephard
- Posted on 8月 25, 2019
- Updated on 7月 5, 2023
- 11019 Views
Forwarding destination prediction enables visibility into how a packet is forwarded through the switch, allowing you to determine which interfaces a packet would egress out of. Typical use cases include, but are not limited to, determining egress members for Port-Channels and ECMPs.
- Written by Aman Aman-Ul-Haq
- Posted on 3月 9, 2021
- Updated on 12月 1, 2023
- 11328 Views
The Segment security feature provides the convenience of applying policies on segments rather than interfaces or subnets. Hosts/networks are classified into segments based on prefixes. Grouping prefixes into segments allows for definition of policies that govern flow of traffic between segments.
- Written by Gary McCarthy
- Posted on 1月 3, 2023
- Updated on 4月 29, 2024
- 5540 Views
Prior to release EOS 4.29.1, a statically configured BGP neighbor, listen range or interface peer could reference a single peer group for inheriting configuration parameters. EOS 4.29.1 adds the ability for that peer group to inherit configuration from up to 8 additional “ancestor” peer groups. The term “leaf peer group” is given to the peer group which is directly referenced by the BGP neighbor, listen range or interface peer.
- Written by Tanuj Kumar Jhamb
- Posted on 10月 20, 2022
- Updated on 7月 11, 2023
- 8228 Views
sFlow is a sampling technique which monitors the incoming traffic on all the interfaces without affecting the network performance.
- Written by Neel Neogi
- Posted on 11月 3, 2021
- Updated on 7月 13, 2023
- 8201 Views
This document describes the support for interface policing counters on interfaces where interface policing feature is configured. Counters for this feature provide information on how many packets are being allowed or dropped on a given interface via the policers configured. The counters are only supported on interfaces where dedicated policers are configured.
- Written by Srinivasan Koona Lokabiraman
- Posted on 6月 29, 2023
- Updated on 7月 4, 2023
- 4874 Views
The internet exit feature enables hosts attached to a VRF in an edge router to reach prefixes that may be reachable over the internet. Since the addresses assigned within a VRF may be non-routable private addresses which cannot be directly used when going to the Internet, the NAT feature is used as a part of the Internet exit solution to provide internet connectivity.
- Written by Pratik Mangalore
- Posted on 12月 14, 2020
- Updated on 11月 13, 2024
- 12486 Views
IP Locking is an EOS feature configured on an Ethernet Layer 2 port. When enabled, it ensures that a port will only permit IP and ARP packets with IP source addresses that have been authorized. As of EOS-4.25.0F release update, IP Locking can run in two modes - IPv4 Locking (which will be referred to as IP Locking) and IPv6 Locking, which can be configured using the commands mentioned in the below sections. IP Locking prevents another host on a different interface from claiming ownership of an IP address through either IP or ARP spoofing.
- Written by Rashid Akhtar
- Posted on 6月 29, 2023
- Updated on 8月 21, 2024
- 4983 Views
This document is an extension to the Decap Group feature, that allows IPv6 addresses to be configured and used as part of a decap group. Now we will be able to configure IPv6 prefixes as a decap group. Tunneled packets with IPv6 destination matching to a configured prefix decap group will be decapsulated and forwarded based on the inner header. IP-in-IP tunnel type will be supported for prefix based decap groups.
- Written by Steve Ulrich
- Posted on 4月 23, 2018
- Updated on 6月 29, 2023
- 6779 Views
IS-IS Counters feature adds support to monitor per interface count of received, transmitted and dropped IS-IS PDUs at the Rib/ISIS agent level. The counters start getting incremented once IS-IS is enabled on an interface and persist until IS-IS is disabled on it or the Rib/Isis agent restart.
- Written by Prakrati Vidyarthi
- Posted on 8月 16, 2018
- Updated on 11月 5, 2024
- 15436 Views
Normally, a switch traps L2 protocol frames to the CPU. However, certain use-cases may require these frames to be forwarded or dropped. And in cases where the L2 protocol frames are forwarded (eg: Pseudowire), we may require the frames to be trapped to the CPU or dropped. The L2 Protocol Forwarding feature provides a mechanism to control the behavior of L2 protocol frames received on a port or subinterface.
- Written by Nishant Sharma
- Posted on 6月 29, 2023
- Updated on 7月 13, 2023
- 4105 Views
This feature adds the capability to filter Lfib routes based on source protocol and prefix. Additionally, source protocol “isis” can be filtered further based on a flexible algorithm name or segment type that can either be a prefix segment or an adjacency segment.
- Written by John Li
- Posted on 2月 16, 2022
- Updated on 7月 18, 2024
- 7796 Views
This TOI describes the MAC limit per VLAN feature which can be used to limit the number of locally learned MAC addresses per VLAN.
- Written by Abdul Haseeb Jehangir
- Posted on 3月 12, 2020
- Updated on 11月 20, 2024
- 11417 Views
Mirror on drop is a network visibility feature which allows monitoring of MPLS or IP flow drops occurring in the ingress pipeline. When such a drop is detected, it is sent to the control plane where it is processed and then sent to configured collectors. Additionally, CLI show commands provide general and detailed statistics and status.
- Written by Ravi Teja Guthikonda
- Posted on 1月 21, 2019
- Updated on 5月 20, 2024
- 5691 Views
Time stamping is an important tool for network engineering and performance analysis. EOS-4.21.3F adds support for payload timestamping of all GRE encapsulated mirrored packets at line rate (initially only supported on the 7500R/7280R/7500R2/7280R2 series). A timestamp is taken on ingress and inserted into the GRE encapsulated mirrored packet payload at egress.
- Written by Pandurangan R S
- Posted on 10月 27, 2023
- Updated on 10月 31, 2023
- 3823 Views
This feature adds support to configure the following QoS OpenConfig models via gNMI QoS Classifiers for classification of incoming traffic. QoS Scheduler Policies for describing scheduling strategies on a port.
- Written by Ajay Kini
- Posted on 11月 2, 2020
- Updated on 7月 3, 2023
- 8134 Views
In a symmetric network topology, for the same ECMP (Equal Cost Multi Path) route programmed at different devices in a switch layer, the various devices can program ECMP next hops in the FEC (Forwarding Equivalence Class) for that route in varying orders.
- Written by Ajay Seshadri
- Posted on 6月 29, 2023
- Updated on 9月 1, 2023
- 6279 Views
This document describes the PFC (priority-based flow control) history counters that are available to debug network oversubscription issues. These counters track statistics on the switch that is sending network traffic at a rate that is more than what its peer can handle.
- Written by David Cronin
- Posted on 3月 3, 2022
- Updated on 3月 14, 2024
- 9628 Views
This document describes a new CLI command to help debug how and why policy permits and denies paths. The aim of this CLI command is for the user to debug a route map or RCF (Routing Control Functions) function by specifying as input a prefix for which BGP has reachability for, either via a BGP peer or a redistribute source.
- Written by Yin Chen
- Posted on 10月 30, 2023
- Updated on 10月 31, 2023
- 4336 Views
This article provides a general introduction to Precision Time Protocol (PTP) supported within EOS. PTP is aimed at distributing time with sub-microsecond accuracy. PTP support is based on the IEEE-1588 specification for version 2 of the protocol.
- Written by Aaron Bamberger
- Posted on 6月 5, 2023
- Updated on 9月 20, 2023
- 5657 Views
Enabling “Proxy ARP/ND for Single Aggregation (AG) VTEP Campus Deployments without EVPN” allows an aggregation VTEP to proxy reply to a VXLAN-encapsulated ARP request/NS when the ARP/NS target host is remote and the ARP/ND binding is already learned by the AG VTEP.
- Written by Sourabh Bollapragada
- Posted on 1月 3, 2023
- Updated on 2月 7, 2024
- 6675 Views
PTP 1-step Boundary Clock (or 1-step BC) is similar to 2-step BC in function but doesn’t send the PTP Follow_Up message. The timestamp present in the PTP Follow_Up message’s preciseOriginTimestamp field is sent in the PTP Sync message’s originTimestamp field along with a non-zero correctionField. This allows us to support more PTP master ports because the control plane does not need to generate PTP Follow_Up messages anymore. PTP 1-step BC supports all the existing features supported by 2-step BC like G8275.1 profile, G8275.2 profile, etc unless otherwise specified in the limitations.
- Written by Mark McClain
- Posted on 3月 1, 2024
- Updated on 3月 1, 2024
- 3419 Views
Python3 is available from EOS 4.22.0 onward.. In all 4.22+ releases, the runtime enables customers to install 3rd party extensions utilizing python3 that do not require the EOS components. Python3 provides built-in virtual environment support, so customers may easily install any required third party modules from Python Package Index (PyPI).
- Written by Ashish Goyal
- Posted on 6月 29, 2023
- Updated on 7月 11, 2023
- 5313 Views
This feature enables Qos policy-maps to match on IPv4/IPv6 fields for L3VPN & 6PE services on the LER device core facing interface, assuming all labels are popped and packets are sent to the customer as IP.
- Written by Deeksha Srivastava
- Posted on 6月 3, 2020
- Updated on 6月 29, 2023
- 9288 Views
VRF Route leaking can be used when routes from one VRF are required in another VRF (e.g. in case of shared services). If VrfLeak Agent is being used to leak routes, the leaked routes (in destination VRF) can be redistributed into IGPs.
- Written by Feng Zhu
- Posted on 6月 29, 2023
- Updated on 7月 13, 2023
- 4704 Views
This feature provides the capability to specify the label stack of the return path from the S-BFD reflector to the S-BFD initiator on the S-BFD initiator, which can be a different path from the shortest/best IGP path from the S-BFD reflector back to the S-BFD initiator, in order that the forwarding of the S-BFD packets would not be impacted by IP routing convergence, i.e., the stability of S-BFD session is not impacted by the IP routing convergence time.
- Written by David Cronin
- Posted on 3月 3, 2022
- Updated on 11月 6, 2024
- 19707 Views
Routing control functions (RCF) is a language that can be used to express route filtering and attribute modification logic in a powerful and programmatic fashion.
- Written by David Cronin
- Posted on 3月 3, 2022
- Updated on 12月 2, 2024
- 12135 Views
Routing Control Functions (RCF) is a language that can express route filtering and attribute modification logic in a powerful and programmatic fashion.The document covers: Configurations of a RCF function for BGP points of application
- Written by Paul Miiller
- Posted on 6月 14, 2021
- Updated on 9月 25, 2024
- 16545 Views
The send support bundle feature adds a new CLI command which creates a ZIP file containing a useful set of logs and
- Written by Romeyo Dsouza
- Posted on 6月 29, 2023
- Updated on 6月 30, 2023
- 4727 Views
Arista has built the link qualification functionality utilizing the SAT engine. There will be 2 sides of the link, the generator port and the reflector port. The generator port will be put in generator mode and the reflector port will be put into reflector mode and then the test will be started on the generator port. Traffic will be transmitted on the generator port and reflected back to the generator port at the reflector port.
- Written by Srinivasan Koona Lokabiraman
- Posted on 6月 29, 2023
- Updated on 7月 4, 2023
- 4706 Views
The service insertion framework is intended to cover the gamut of features related to service insertion.
- Written by Karan Jagjit Kumar
- Posted on 6月 29, 2023
- Updated on 2月 15, 2024
- 5972 Views
Smart System Upgrade (SSU) provides the ability to upgrade the EOS image with minimal traffic disruption. This is an existing feature on many fixed system products. This resource will outline the SSU feature in reference to CCS-720DP, CCS-722XPM, CCS-720XP-96ZC2 and DCS-7010TX.
- Written by Deepak Vijayakumar
- Posted on 8月 31, 2023
- Updated on 9月 12, 2023
- 3663 Views
Storm control allows users to configure a traffic level above which incoming broadcast, unknown-unicast and multicast traffic on a port gets dropped, thus preventing flooded traffic from bringing the switch down.
- Written by Chalermek Intanagonwiwat
- Posted on 6月 29, 2023
- Updated on 7月 11, 2023
- 4297 Views
This feature is designed to be used in an L3 centric network where servers communicate using IPv4/IPv6 packets over VXLAN. The IP packets are all expected to be routed in this network. Since L2 information is not relevant in routing, some customers may prefer to send their packets with random destination MAC addresses over VXLAN to minimize L2 overhead.
- Written by Aurora Desmarais
- Posted on 6月 29, 2023
- Updated on 6月 30, 2023
- 5247 Views
sFlow is a multi-vendor sampling feature that helps to monitor application level traffic flow. For ingress sFlow, sampling can be configured on a set of interfaces and port-channels where the application data is flowing inbound.
- Written by Shan Zhang
- Posted on 6月 29, 2023
- Updated on 11月 6, 2024
- 4768 Views
Generic UDP Encapsulation (GUE) is a general method for encapsulating packets of arbitrary IP protocols within a UDP tunnel. While GUE supports an extensible header format with optional data, currently we only support the variant 1 header format, which directly encapsulates the IPv4/IPv6 payload without a GUE header.