Policy Based Routing (PBR) is a feature that is applied on routable ports, to preferentially route packets.  This is

Port Security: Protect mode (PortSec Protect) is newly added to the Port Security feature and is designed to restrict

Port Channel member status logging on Arista switches allows logging of Ethernet interfaces joining or leaving a

TOI Chicago

Starting EOS 4.15.0F, a BGP route reflector can preserve the BGP attributes (next hop, local preference and metric)

This document describes the enhancements to Arista's IEEE 1588 PTP implementation introduced in EOS 4.15.0F.

This feature makes ARP and ND packets use a higher priority output queue when software forwarded on the switch. Doing

Since, now there can be multiple inputs, conflicts may arise. Non conflicting configurations are when non default

TOI 4.17.0F QoS

QSFP+ modules that support TX power DOM will now display the reported TX power value via show interfaces transceiver.

Forward Error Correction (FEC) is required with some QSFP100 media to achieve error free operation of the link when

RACL divergence enables the optimization of the utilization of hardware resources by installing ACLs only on the

TCAM sharing between different VLAN Interfaces when they have same ACL attached : Configurable via CLI

With the 13.0 release, CloudVision Cognitive Unified Edge (CV-CUE) can redirect onboarding clients to a dynamic URL defined by the RADIUS. If the  RADIUS access-accept request has a role and a redirection URL for a client, access points (AP) can redirect such client’s HTTP or HTTPS requests. 

Some data plane features on some switch platforms may require packets to be recirculated through the switch chip in

This feature allows to advertise routes learnt via BGP into IS IS network or IS IS routes into BGP network. It also

This feature removes an ARP entry when the physical port, on which the ARP entry's MAC address is learned, goes down.

TOI

Arista WM gathers a wealth of data about the wireless deployment. The data gathered includes Wireless Intrusion

Equal Cost Multi path (ECMP) provides the ability to load share traffic across multiple next hops.

TOI 4.20.1F

The transmit power configured on UI is now treated as EIRP (Equivalent Isotropically Radiated Power) instead of

The BGP labeled unicast (LU) RFC is used to advertise BGP routes with a stack of MPLS labels, thereby allowing

This feature provides support for advertising IPv4 unicast Network Layer Reachability Information (NLRI) with

BGP TOI 4.17.0F

EOS 4.17.0F adds support for IPv4 address family in OSPFv3 (multiple address family support) based on RFC5838.

Multi Agent, Platform independent. This feature supports RFC 7606, which  provides improved security and

TOI 4.20.1F

The broadcast queue towards the CPU is shared among all interfaces of the forwarding chip. So broadcast storm on a

This feature allows routing traffic across two Vrf domains on the same switch using an external loopback cable

In an MLAG setup, routing on a switch (MLAG peer) is possible using its own bridge/system MAC, VARP MAC or VRRP MAC.

With the 13.0 release, you can integrate SAML SSO with a captive portal for authentication. The SAML integration functionality is only available for captive portals hosted on the Arista Cloud. It is not available if the captive portal is hosted on third-party servers or on the access point.

Sampled Mirroring is an extension of the Mirroring feature and sampling is a property of the

With the 13.0 release, you can schedule the Automatic Channel Selection (ACS) to run at a specific time of the day and minimize service disruption.

Secondary private VLAN trunk ports are introduced in the EOS 4.15.2F release. This feature can

Selective Q in Q tunneling feature allows a set of customer VLANs (hereafter referred to as c vlan(s)) to be tunneled

On 7500E, sFlow output interface feature enables sFlow to use the hardware provided output interface and

ACL based QoS programmed on SVIs can share hardware resources starting from EOS 4.17.0F. This results in

TOI 4.17.0F QoS

OpenStack has a concept of shared tenant networks which let the admin can create a network which can be shared by all the

The show command 'show qos interface fabric' was introduced for DCS 7250QX and DCS 7300X series starting EOS

TOI 4.17.0F QoS

Delay request messages can now be set from log 7 to 8. To configure: switch(config)#interface Et5/1.

Nexthop groups is an existing feature which allows users to manually configure a set of tunnels with nexthops.

Hardware Table Capacity Monitoring is an existing feature to keep track of the capacity and utilization of various

Starting 8.8 release, Cloud customers can receive all events/alerts as SNMP traps. While configuring an SNMP trap

Source ARP with a virtual IP is a new VARP feature. The purpose of this feature is to change the ARP request header's

With the 13.0 release, you can enable spatial reuse from CloudVision Cognitive Unified Edge (CV-CUE) to improve the spectral efficiency and optimally allocate resources to meet the Quality of Service (QoS). With spatial reuse, two or more Wi-Fi devices (AP or client) that support 802.11ax protocols can send transmissions simultaneously without any significant data loss.

Spectrum analysis is a tool to analyze the RF environment for interference. For monitoring and troubleshooting of wireless networks, you must be aware of the RF environment in which the  APs operate.

This is an infrastructure that provides management of SSL certificates, keys and profiles. Only RSA keys are

Stateful switchover is a redundancy mode available on systems with 2 supervisor cards. One supervisor card is active

TOI 4.20.6F

Static ARP inspection is a security feature that verifies the source IP and the source MAC addresses of each received

This feature enables configuring static IPv4 routes that specify the next hop by using an IPv6 address instead of an

Static multicast feature brings in capability to statically configure multicast routes on any Arista platform

A number of L4 7 appliances use the same MAC address to load balance services across two or more appliances that form the

Packet counters for Static and Twice NAT connections are now supported on the DCS 7150 series. This is a debug

The existing storm control interface configuration mode CLI commands have been extended to support the new

A traffic storm is a flood of packets entering a network, resulting in excessive traffic and degraded performance.